background image

  32 

Martin PDE Junction Box / Break-In / Break-Out Cable user guide 

 

 

 

Disposing of this product 

Martin™ products are supplied in compliance with Directive 2012/19/EC of the European 
Parliament and of the Council of the European Union on WEEE (Waste Electrical and 
Electronic Equipment), where applicable. Help preserve the environment! Ensure that 
this product is recycled at the end of its life. Your supplier can give details of local 
arrangements for the disposal of Martin products

 

 

FCC Compliance 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 
device may not cause harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation. 

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference 
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or more of the following measures: 

—Reorient or relocate the receiving antenna. 

—Increase the separation between the equipment and receiver. 

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

—Consult the dealer or an experienced radio/TV technician for help. 

Supplier’s Declaration of Conformity 

Harman Professional, Inc. have issued an FCC Supplier’s Declaration of Conformity for this product. The 
Declaration of Conformity is available for download from the Active Junction Box  area of the Martin website at 
www.martin.com 

Canadian Interference-Causing Equipment Regulations - 

Règlement sur le Matériel Brouilleur du Canada 

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment 
Regulations CAN ICES-3 (B)/NMB-3(B) and CAN ICES-005 (B) / NMB-005 (B). 

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le Matériel Brouilleur du 
Canada. 

EU EMC 

Not for use in a computer room as defined in the Standard for the Protection of Information Technology Equipment, 
ANSI/NFPA 75. 

Ne peut être utilisé dans une salle d'ordinateurs telle que définie dans la norme ANSI/NFPA 75 Standard for the 
Protection of Information Technology Equipment.

 

 

 

Summary of Contents for Martin Active Junction Box Power-DMX-Ethernet to...


































Reviews: