background image

Harman®  •  P43 Installation Manual_R23  •  2008 -___  •  04/14

10

3-90-04301i

Termination Location and Vent Information 

 

A.  Vent Termination Minimum Clearances

Figure 4.1

Figure 4.2

#1 Preferred method 

(Figure 4.1)

This method provides excellent venting for normal operation 

and allows the stove to be installed closest to the wall. Two 

inches  from  the  wall  is  safe;  however,  four  inches  allows 

better access to remove the rear panel. The vertical portion of 

the vent should be three to five feet high. This vertical section 

will help provide natural draft in the event of a power failure.
Seal pipe joints with silicone or aluminum tape in addition to 

the sealing system used by the manufacturer.

Note: Do not place joints within wall pass-through.

#2 Preferred method 

(Figure 4.2)

This  method  also  provides  excellent  venting  for  normal 

operation but requires the stove to be installed farther from 

the wall. The vertical portion of the vent should be three to 

five feet high and at least 1” from a combustible wall. This 

vertical section will provide natural draft in the event of a 

power failure.
Seal pipe joints with silicone or aluminum tape in addition to 

the sealing system used by the manufacturer.
If  the  stove  is  installed  below  grade  be  sure  the  vent 

te

rmination is at least 12" above grade 

(with outside air 

only)

. The outlet must also be 1 foot from the house/building.

Note: Do not place joints within wall pass-through.

CAUTION

!

Keep combustible materials (such as grass, leaves, 

etc.) at least 3 feet away from the flue outlet on the 

outside of the building.

3 Ft.

to

Combustibles

3 Ft.

to Combustibles

3 Ft.

to

Combustibles

3 Ft.

to Combustibles

Summary of Contents for P43

























Reviews: