background image

Harman®  •  P43 Installation Manual_R23  •  2008 -___  •  04/14

19

3-90-04301i

Inspect appliance and components for damage. 

Damaged parts may impair safe operation.
•  Do NOT install damaged components.

•  Do NOT install incomplete components.

•  Do NOT install substitute components.
Report damaged parts to dealer.

I.  Fire Safety

To provide reasonable fire safety, the following should be 

given serious consideration:
•  Install at least one smoke detector and CO detector on 

each floor of your home.

•  Locate smoke detector away from the heating appliance 

and close to the sleeping areas.  

•  Follow the smoke detector manufacturer’s placement and 

installation instructions and maintain regularly.  

•  Conveniently locate a Class A fire extinguisher to contend 

with small fires.

•  In the event of a hopper fire:
 

•  Evacuate the house immediately.
•  Notify fire department.

J. Inspect Appliance & Components

•  Remove  appliance  and  components  from  packaging 

and inspect for damage.

•  Report to your dealer any parts damaged in shipment.
• 

Read all the instructions before starting the 

installation. Follow these instructions carefully 

during the installation to ensure maximum safety 

and benefit.

•  Installation and use of any damaged appliance. 

•  Modification of the appliance.

•  Installation  other  than  as  instructed  by  Hearth  &  Home 

Technologies.

•  Installation and/or use of any component part not approved 

by Hearth & Home Technologies.

•  Operating  appliance  without  fully  assembling  all 

components.

•  Do NOT Overfire.

Or any such action that may cause a fire hazard.

Fire Risk.

Hearth  &  Home Technologies  disclaims  any 

responsibility for, and the warranty will be voided 

by the following actions: 

WARNING

!

WARNING

!

Summary of Contents for P43

























Reviews: