background image

24

3-90-07205R26_10/14

Fuel and Fuel Storage

Pellet  fuel  quality  can  fluctuate  from  manufacturer  to 

manufacturer, and even from bag to bag. 

Hearth & Home Technologies recommends using only fuel 

that is certified by the Pellet Fuels Institute (PFI).
Fuel Material

•  Made from sawdust and/or other wood by-products

•  Source material typically determines ash content
Higher Ash Content Material

•  Hardwoods with high mineral content

•  Bark and leaves as source material

•  “Standard” grade pellets, corn and other biomass
Lower Ash Content Material

•  Softwood; pine, fir, etc.

•  Materials with lower mineral content

•  “Premium” grade pellets
Clinkers

Minerals  and  other  non-combustible  materials,  like  sand, 

will turn into a hard glass-like substance when heated. 

Trees from different areas will vary in mineral content. For 

this  reason,  some  fuels  will  produce  more  clinkers  than 

others.
Moisture

Always  burn  dry  fuel.  Burning  fuel  with  high  moisture 

content takes energy to dry and tends to cool the appliance 

thus, robbing heat from your home. Damp pellet fuel could 

turn back into sawdust which does not flow properly through 

the feed system.

Size

•  Pellets  are  either  1/4  inch  or  5/16  inch  (6-8mm)  in 

diameter

•  Length should be no more than 1-1/2 inches (38mm)

•  Pellet  length  can  vary  from  lot  to  lot  from  the  same 

manufacturer

Tested  and  approved  for  use  with  wood  pellets  ONLY. 

Burning of any other fuel will void your warranty.

Hearth & Home Technologies is not responsible for 

stove  performance  or  extra  maintenance  required 

as a result of using fuel with higher ash or mineral 

content.

NOTICe

Fuel Specifications

Performance

•  Higher ash content requires more frequent maintenance.

•  “Premium” grade pellets will produce the highest heat 

output.

•  Burning  pellets  longer  than  1-1/2  inches  (38mm)  can 

cause inconsistent feeding and/or ignition.

We recommend that you buy fuel in multi-ton lots whenever 

possible.  However,  we  do  recommend  trying  different 

brands  prior  to  purchasing  multi-ton  lots,  to  ensure  your 

satisfaction.

When  changing  from  “Premium”  grade  pellets  to  a 

“Standard” or “Economy” grade fuel, the FEED ADJUSTER 

will  likely  need  adjusted  to  a  lower  setting.  When  under 

maximum demand, ensure there is no unburned fuel being 

pushed into the ash pan.
Storage

•  Wood pellets should be left in their original sealed bag 

until ready to use, to prevent moisture.

•  Do not store fuel within the specified clearance areas, 

or in a location that will interfere with routine cleaning 

and maintenance procedures.

CAUTION

!

Tested and approved for use with wood pellets ONLY. 

Burning of any other fuel will void your warranty.

CAUTION

!

Summary of Contents for PB 105





















































Reviews: