background image

© 2015Harmar Mobility, LLC • All Rights Reserved

|  www.harmar.com

12

Pinnacle 101 Stair Lift

INSTALLATION PROCEDURES

Figure 12-1

1. 

If the LED indicator light is not green, check the 

safety senors:

• 

Seat swivel sensor (seat should be in the 
locked position)

• 

Footrest lower sensor (check by pushing in 
on the safety pan on the footrest)

• 

Upper foot pan safety sensor (check by 
pushing on the safety pan on the footrest).

• 

Front foot pan safety sensor (check by 
pushing on the safety pan on the footrest).

• 

Uphill safety sensor (ensure nothing is 
blocking upward passage)

• 

Downhill safety sensor (ensure nothing is 
blocking downward passage)

If the LED indicator light is still not green after 
testing sensors, turn the unit off and re-check all 
wire plugs. Turn the unit on again and re-check the 
LED indicator light cycle. When the LED indicator 
light remains green the lift is ready to operate. 

[Figure 12-1]

F. LED & AUDIBLE TONES  

2. TONES INFORMATION
Minor faults

Single long beep (will reset once fault is cleared)

• 

Seat swiveled out of position

• 

Edge safety detected

• 

Under foot rest

• 

Current overload condition

• 

A Low battery voltage condition

Pulsing Beep

Lift stopped off of charge strip. Will sound after 30 
second for 30 seconds. It will repeat ever 10 minutes 
until lift is operated or returned to charge strips.

Tones    

Beeps

Runaway   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1
No Power  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 
Conflicting Switches Footrest UP & Footrest DOWN   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3  
Conflicting Switches Obstruction UP & Obstruction Down . . . . . . . . . . . . . . . . . . . . . . . . .4
Conflicting Switches Footrest DOWN & Obstruction UP   . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
Conflicting Switches Footrest UP & Obstruction DOWN   . . . . . . . . . . . . . . . . . . . . . . . . . . .6 
Conflicting Switches STOP UP & STOP DOWN switches both Detected  . . . . . . . . . . . . .7 
Conflicting Switches STOP UP & STOP DOWN switches both not Detected  . . . . . . . . .8 
Helix Only LIMIT Switch Dectected   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Major Fault Codes

Summary of Contents for SR601





















Reviews:

Related manuals for SR601