background image

TEC0081     20150915   P/N: 630-00065            revA

SR601 • Pinnacle 101 Stair Lift Installation 

 15

Pinnacle 101 Stair 

COMPLETION PROCEDURES

7. 

Test to ensure that the lift can only be driven 

away from the obstruction. The LED indicator light 
will turn to green and stop beeping indicating a safe 
operating condition.

8.

 Repeat the above tests while driving the lift in 

opposite direction.

9. 

If any safety condition does not function properly, 

carefully review all installation instructions, reset the 
“ON /OFF” switch and check that the LED indicator 
light is green. Repeat the above tests.

10.

 If any safety stop switch fails to immediately 

stop the lift and/or a red LED indicator light appears, 
remove the key to prevent further use of the lift and 
immediately call the manufacturer for assistance 
in diagnosing and repairing the problem. 

DO NOT 

USE THE LIFT.

E. ADDITIONAL SYSTEM CHECKS

1. 

After the successful testing of all safety switches, 

sit on the lift and operate to the top of the stairs. 
Keeping the control switch depressed continuously, 
the lift should gently decelerate and then stop at 
the top of the rail.

2.

 As a final adjustment, sit on the lift and do two 

(2) complete up trips and stop with the chair at 
the bottom. Then tighten the compression screw 
in the top end plate, then run the chair to the top 
and again tighten the compression screw. Run the 
chair to the middle and do a final tightening of the 
compression screw.

3. 

Drive the lift to the bottom, keeping the control 

switch depressed all the time, and check that the lift 
gently decelerates and stops so the footrest pan is 
clear of the floor. If necessary adjust the limit cams 
with a 5/64” Allen wrench.

4.

 Move the lift about 3 ft from either the top or 

bottom of the rail. After 30 seconds the armrest 
LED indicator light  will show orange and beep 
indicating that the lift is not positioned on a charge 
point. The beep will stop after 30 seconds, but the 
armrest LED indicator light will continue to flash 
orange. 

5.

 Test the seat swivel at the top by using the levers 

and swiveling the seat towards the landing and 
stop the seat at 35 and 85 degrees. The seat swivel 
levers will release into a locked position at each of 
these angles. The lift will not operate in any of these 
positions if the control switch is depressed, and the 
LED indicator light will turn orange. Return the seat 
to its normal position and the LED indicator light will 
turn green and the lift will now operate normally.

Summary of Contents for SR601





















Reviews: