background image

SAFETY: 

 

Caution:  

Do not operate this lift until your dealer has satisfactorily instructed you in the proper operation of the 

lift. 

 

Your Harmar  Lift has been engineered and designed for years of trouble free use.  Although, with everyday use, 
some parts may become loose or worn.  

IMPORTANT!  

Check regularly for any worn, loose or damaged parts of 

your lift.  

If anything is observed, DO NOT USE THE LIFT!  

Contact your dealer or installer of the lift for repairs 

to be made

.  Failure to act may cause severe injury!

 

 

Your Harmar Lift should only be used for the loading and unloading of scooters and power wheelchairs for which 
it is designed.  DO NOT add to or modify any part of the lift system without first contacting the manufacturer of the 
lift.  Any modifications may void any warranties as well as effect the structural integrity of the lift. 

 

ALWAYS CHECK THE LIFTING STRAP BEFORE EACH USE FOR DAMAGE OR WEAR. 

 

Always make sure the vehicle’s parking brake is firmly set before operating the lift. 

 

Caution:  

Insure that the Lifting Strap is secure and taught and that it points straight down before lifting of the 

scooter or power chair.  Failure to do so could result in the scooter or chair swinging toward the operator of the 
vehicle. 

 

Caution:  

When using the lift, keep your hands and feet from under the scooter or power chair as it is being 

loaded or unloaded. 

 

Caution:  

Stop lifting before the Strap Hook contacts the Strap Roller mounted on the Lifting Arm.  Contact will 

result in damage to the lift.  A properly adjusted and operated lift will avoid this. 

 

Caution:  

Insure that the scooter or chair is firmly sitting on the floor of the vehicle and not suspended by the lift.  

If the scooter or power chair is not firmly on the floor of the vehicle, it may move during transportation and cause 
damage to the lift, scooter or power chair, vehicle, or passengers. 

 
 

 

MAINTENANCE: 

 
The Harmar  Lift has been designed to be as trouble free as possible for the owner.  But, as with any mechanical de-
vice, regular care should be given while owning and using this device. 
 
Maintenance is no exception. 
 

We recommend that dealers should schedule a preventative maintenance inspection at least once a year on   
motors, lift frame, wiring harness and all moving parts of the lift. 

 

Check for paint chips and touch up any bare metal with a good gloss black enamel or lacquer to inhibit rust.  This 
may be necessary more frequently when subjected to salt air or road salt. 

 

Always check the lifting strap before each use.  If any wear or fraying is noticed DO NOT USE THE LIFT!  Con-
tact the installer or dealer for repair.  Failure to act may cause damage to the vehicle or severe injury! 

 

Hand control units should not be exposed to the weather.  If the lift is mounted in the bed of a truck, remove the 
hand control between each use.  Exposure to the elements may cause the unit to fail. 

 
WARRANTY: 

 
This lift is covered by a one year factory warranty on materials and workmanship.  Contact your local dealer for more 
information or go to www.harmar.com for complete details. 

Summary of Contents for AL065











Reviews: