background image

- 2 -

V6-04-05

Assembly instructions Veranda sunblind VZ520

A. Introduction:

The Harol veranda awning is an outside sun protection to be fitted on top of the veranda. This sun 
protection blocks the sun rays and in doing so protects the veranda against overheating. Thanks to the 
special and manyfold fastening accessories, this sun protection can be fitted onto all existing veranda 
profiles.

With this manual we confine ourselves to the instructions regarding the perfect installation of our sun 
proctection. The contractor assumes full responsibility for the installation of the complete sun protec-
tion and all possible components added by this very contractor. Contractor is also held accountable for 
the correct CE-labelling of the sun protection installed under his responsibility. This manual is meant 
to be used by professionals only. It is not to be used by DIY-enthusiasts or apprentice fitters.

B. General warnings !

For a safe fitting, use and maintenance of this sun protection a number of precautions have to be 
taken. For the safety of everyone concerned, please do take notice of the following general warnings !

!  This manual is meant to be used by professionals only! It is not to be used bij DIY-enthusiasts or 

apprentice fitters.

! Before you start ,please do read these instructions thoroughly.
!  The tightening of springs creates important powers. Be very careful and make sure of a solid footing 

whilst operating.

!  Provide sufficent light in the fitting area. Dispose of obtsacles and dirt. Make sure that, except for 

the fitters, no other people are in the fitting area. Unauthorized people might be in the way or at risk 
themselves.

!  Whilst operating the system, you must be able to overlook the complete area and the whole of the 

sun protection. There are a number of places where people might get injured. Especially watch the 
following parts where people might risk getting jammed : the extension pole, the intermediate rol-
lers, the bench, the guide rails and the casing.

!  Electrical connections have to be made in accordance with the existing local norms and require-

ments.

Guarantee and conditions :
-  Harol has endeavered to design and assemble this sun protection in accordance with the ruling and 

valid CE-norms. Nevertheless, feel free at any time to countercheck these interpretations with your 
local national institute of normation. 

-  From this manual no rights can be derived. Technical alterations are possible without prior notifica-

tion. 

-  When dealing with larger projects, we do advise you to implement a full installation of 1 sun protec-

tion before starting with the installation of the rest of the sun protections. This way, an oversight or a 
small mistake can be detected in its earliest and least expansive stadium.

- For our general conditions of sale: see pricelist. 

Veranda sun-blinds have been designed as a sun protection and for that reason  may 
not be used as an all-weather protection. In case of heavy rain or wind the sun-blind 
has to be closed immediately. Therefore we recommend to use the sun protection in 
combination wth an automated wind/sun – control.

Summary of Contents for VZ520


















Reviews: