background image

R

R

Turbo Vac TV60R

Replacement Parts

SAFETY WARNING!

Use genuine factory parts or parts with

equivalent characteristics including: type,

strength and material. Failure to do so

may result in voidance of warranty,

product malfunction or possible injury to

operator and others.

•  

Replace locknuts and locking screws if

 

they can be tightened without

 

considerable resistance for several  

 

turns before they are completely tight.

•  

If hardware is not secure, or if some of  

 

the fasteners are over-tightened, 

 

equipment failure may result, posing  

 

possible safety hazards.

•  

Use proper torque specifications for all

 

fasteners when they are replaced.

Gasoline

SAFETY WARNING!

Gasoline is extremely flammable and can

be highly explosive.

•  

Always use an approved container for

 gasoline.

•  

Do not allow open flames or sparks  

 

while performing maintenance or refu- 

 eling.

•  

Never remove the fuel tank cap or add

 

gasoline when the engine is running or

 

while it is hot.

•  

Never fill the fuel tank indoors. Gaso- 

 

line fumes are heavy and will sink to the

 

lowest point, collecting and becoming

 

increasingly hazardous. One part 

 

gasoline in 20 parts air will explode  

 

easily and violently.

•  

Wipe up spilled gasoline immediately.

•  

Do not store gasoline in a room with an

 

appliance that has a gas pilot or elec- 

 

trical switch that may cause sparks.

•  

Always store gasoline outside in a 

 

safety can (a can that has a flame 

 

arrestor and pressure relief valve in  

 

pour spout).

•  

Never store the equipment with gaso- 

 

line in the tank inside a building where  

 

fumes may reach an open flame or  

 spark.

•  

Allow the engine to cool before storing  

 

in any enclosure.

•  

Be certain to provide adequate ventila- 

 

tion if an engine must be run indoors -  

 

exhaust fumes are dangerous.

Hydraulics

SAFETY WARNING!

HIGH-PRESSURE FLUID HAZARD!

Escaping fluid under pressure can

penetrate skin and cause serious injury

or death.

To prevent serious injury or death:

•  

Relieve pressure on system before

 

repairing, adjusting or disconnecting.

•  

Wear proper hand and eye protection

 

when searching for leaks.

•  

Use wood or cardboard instead of  

 

hands when looking for leaks.

•  

Keep all hoses, fittings and compo- 

 

nents in good repair.

•  

Do not use any type of heat or flame

 

(welding, soldering, cutting torch, etc.)

 

near pressurized hydraulic lines.

11

Summary of Contents for TURBO VAC 60R

































































Reviews: