background image

 

P-K DURATION II 

™ Indirect Domestic Water Heating System 

 

2.2 

T

RAINING

 

Proper training is the best protection against accidents.  Factory training sessions are available to qualified 
individuals who are sponsored by the local Harsco Industrial, Patterson-Kelley representative. 
 

 
It is 

essentia

l to read, understand, and follow the 

recommendations of this manual before installing, 
operating, or servicing this equipment.  Failure to do so 
could result in fire or explosion and serious injury, death, 
and/or property damage. 
 

 
Operating  and  service  personnel  must  be  thoroughly  familiar  with  the  basic  construction  of  the  P-K  Duration  II 
system,  the  location  and  operation  of  the  controls,  adjustment  of  their  various  mechanisms,  and  all  applicable 
safety  precautions.    If  any  of  the  provisions  of  this  manual  are  not  fully  and  completely  understood,  contact 
Harsco Industrial, Patterson-Kelley Technical Service at 570.476.7261 or toll free at 877.728.5351. 

 

2.3 

S

AFETY 

F

EATURES

 

It is the responsibility of the customer to maintain the safety features, such as but not limited to: guards, safety 
labels, safety controls, interlocks, lockout devices and pressure relief valves. 

 

2.4 

S

AFETY 

L

ABELS

 

The following words are used in this manual to de-note the degree of seriousness of the individual hazards.   

 Indicates an imminently hazardous situation which, if not avoided, 

will

 result in death 

or serious injury. This signal word is to be limited to the most extreme situations. 
 

 Indicates a potentially hazardous situation which, if not avoided, 

could

 result in death 

or serious injury.

 

 

 Indicates a potentially hazardous situation which, if not avoided, 

may

 result in minor or 

moderate injury.  It may also be used to alert against unsafe practices.

 

 
NOTICE/NOTE

 - NOTICE is the preferred signal word to address practices not related to personal injury. The 

safety alert symbol is not used with this signal word.

 

 

 
 
 
 
 
 

Summary of Contents for P-K DURATION II D2DW-30(S/D)





























Reviews: