9 – English
OPERATION
CONNECTING/DISCONNECTING AIR HOSE
(HOSE NOT PROVIDED)
See Figure 2, page 13.
WARNING:
Never exceed the air tool’s pressure rating as
recommended by the manufacturer. When using this
air compressor as an inflation device, always follow the
maximum inflation guidelines stated by the manufacturer
of the item being inflated.
Make sure the air compressor is turned off and the battery
pack is not installed.
Rotate pressure regulator knob fully in the counter-
clockwise direction so that the outlet pressure is at
zero (0) psi.
Attach hose with quick connect air fitting to 1/4 in. quick
coupler on air compressor. Make sure to push the hose
adaptor end fully into the coupler until the sleeve springs
forward to lock it in place.
To disconnect an air hose or an air tool:
Confirm that the outlet pressure is at zero (0) psi.
When disconnecting a hose from 1/4-in. quick coupler,
always firmly hold release end of hose.
Pull back on the release sleeve on the 1/4-in. quick
coupler.
With a firm grip, pull out the quick-connect air fitting that
is attached to the quick coupler.
BREAK-IN PERIOD
Before first use, install a fully charged 4.0 Ah battery pack,
then run the air compressor at zero tank pressure with the
drain valve fully open for 30 minutes or until the battery pack
is completely discharged, whichever happens first.
TURNING THE AIR COMPRESSOR ON/OFF
See Figure 3, page 14.
Install the battery pack.
Move the Auto On/Off switch to the
AUTO ON (I)
position
to power the compressor on.
To turn the air compressor off, move the Auto On/Off
switch to the
OFF (O)
position.
NOTE:
When the compressor is in the
AUTO ON (I)
position,
the air compressor will automatically turn back on when
the designated tank air pressure drops below the preset
pressure limit. It will also shut off again when the cut-off
pressure is reached.
WARNING:
Never exceed the air tool’s pressure rating as
recommended by the manufacturer. When using this
air compressor as an inflation device, always follow the
maximum inflation guidelines stated by the manufacturer
of the item being inflated.
WARNING:
Always ensure the switch is in the
OFF (O)
position and
the regulator pressure gauge reads zero before changing
air tools or disconnecting the hose from the air outlet.
Failure to do so could result in possible serious personal
injury.
USING THE AIR COMPRESSOR
See Figure 4, page 14.
WARNING:
Risk of bursting.
Do not adjust pressure regulator
knob to result in output pressure greater than marked
maximum pressure of attachment and/or the item being
inflated. Never use at pressure greater than 120 psi.
Failure to heed this warning could result in possible
serious personal injury.
WARNING:
Air powered tools may require more air consumption
than this air compressor is capable of providing. Check
the tool manual to avoid damage to the tool or risk of
personal injury.
Ensure that the Auto On/Off switch is in the
OFF (O)
position and the battery pack is not installed.
Attach air hose following the instructions in
Connecting/
Disconnecting Air Hose
(hose not provided).
Attach 1/4 in. NPT quick-connect air fitting to the
accessory or tool you intend to use.
Insert the other end of the quick-connect air fitting to the
quick coupler on the open end of hose.
Install the battery pack.
Move the Auto On/Off switch to the
AUTO ON (I)
position.
Set the amount of air pressure desired using the pressure
regulator knob. Turn the knob clockwise to increase or
counterclockwise to decrease the air pressure through
the hose.
NOTE:
Always use the minimum amount of pressure nec-
essary for your application. Using a higher pressure than
needed will drain air from the tank more rapidly, cause the
unit to cycle on more frequently, and reduce battery run
time between charges.
Following all safety precautions in this manual and the
manufacturer’s instructions in the air tool manual, you
may now proceed to use your air-powered tool.
Summary of Contents for HPCP01
Page 35: ...NOTES NOTAS...
