background image

4

5

IMPORTANT

: There is a minimum safe impedance so be sure to check the manu-

facturer’s recommended impedance for your amplifier to avoid any damage to your 

amplifier or voiding your warranty. 

Connecting the AK410 and AK115 
to Your Amplifier

The 

AK410 and AK115

 connections 

are made via either the 1/4” phone 

jacks or Speakon connectors located 

on the rear panel jack-plate. Be sure 

to make your connection with un-

shielded speaker cable. Connect the 

Amplifier Output to the speaker Input 

on the AK410’s or AK115’s rear jack-

plate.

Using the EXTENSION Output

The 

AK410 and AK115

 provides a 

convenient Extension Output for 

connecting additional speaker cabi-

nets in parallel. Be sure to read the 

section above on impedance to 

insure a proper hook-up with your 

amplifier.  Follow the steps below to 

connect two 

AK410 or AK115

's using 

the Extension Output.  Connect the 

Amplifier Output to the Input of the 

first 

AK410 or AK115

. Now, connect 

the Extension Output to the Input of 

the second cabinet.

Hartke Systems

Distributed Exclusively by

Samson Technologies Corp.

Hicksville, New York 11802

MODEL 2000

200 WATTS

8

?

= 120 WATTS

4

?

= 200 WATTS

CAUTION

TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-

ABLE  PARTS  INSIDE. REFER  SERVICING TO  QUALIFIED  

SERVICE  PERSONNEL. TO   PREVENT   FIRE  OR  SHOCK 

HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE.

ASSEMBLED IN R.O.K.

SERIAL NUMBER

115

~ AC INPUT

115V/230V 50/60Hz

FUSE

5A/250V, 180W (115V)

2.5A/250V, 450W (230V)

SPEAKER OUTPUTS

8

8

ON

OFF

HPF

EFFECT

SEND

RETUIRN

8

Connecting the AK410 and AK115 

Hartke Systems

Distributed Exclusively by

Samson Technologies Corp.

Hicksville, New York 11802

MODEL 2000

200 WATTS

8

?

= 120 WATTS

4

?

= 200 WATTS

CAUTION

TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-

ABLE  PARTS  INSIDE. REFER  SERVICING TO  QUALIFIED  

SERVICE  PERSONNEL. TO   PREVENT   FIRE  OR  SHOCK 

HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE.

ASSEMBLED IN R.O.K.

SERIAL NUMBER

115

~ AC INPUT

115V/230V 50/60Hz

FUSE

5A/250V, 180W (115V)

2.5A/250V, 450W (230V)

SPEAKER OUTPUTS

8

8

ON

OFF

HPF

EFFECT

SEND

RETUIRN

8

Summary of Contents for AK115













Reviews: