background image

 

17 

 

 
 
 
 
 
 

Harvest Tec, LLC. Warranty and Liability Agreement.  

 

Harvest Tec, LLC. will repair or replace components that are found to be defective within 12 months 
from the date of manufacture.  Under no circumstances does this warranty cover any components 
which in the opinion of Harvest Tec, LLC. have been subjected to negligent use, misuse, alteration, 
accident, or if repairs have been made with parts other than those manufactured and obtainable from 
Harvest Tec, LLC.   
 
Our obligation under this warranty is limited to repairing or replacing free of charge to the original 
purchaser any part that in our judgment shows evidence of defective or improper workmanship, 
provided the part is returned to Harvest Tec, LLC. within 30 days of the failure.  Parts must be 
returned through the selling dealer and distributor, transportation charges prepaid.   
 
This warranty shall not be interpreted to render Harvest Tec, LLC. liable for injury or damages of any 
kind, direct, consequential, or contingent, to persons or property.  Furthermore, this warranty does not 
extend to loss of crop, losses caused by delays or any expense prospective profits or for any other 
reason.  Harvest Tec, LLC. shall not be liable for any recovery greater in amount than the cost or 
repair of defects in workmanship.   
 
There are no warranties, either expressed or implied, of merchantability or fitness for particular 
purpose intended or fitness for any other reason.   
 
This warranty cannot guarantee that existing conditions beyond the control of Harvest Tec, LLC. will 
not affect our ability to obtain materials or manufacture necessary replacement parts.   
 
Harvest Tec, LLC. reserves the right to make design changes, improve design, or change 
specifications, at any time without any contingent obligation to purchasers of machines and parts 
previously sold. 
 
Revised 7/22 

 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for 500A1



















Reviews: