Haskris R1600 Instruction Manual Download

Page: 42 / 56

Haskris Model R1600 No Load Start-Up Checklist

www.haskris.com

Version R1600-X-R407C-XXX Instruction Manual Rev00

No Load Start

No Load Start----Up

Up Checklist for Haskris

Checklist for Haskris

Checklist for Haskris R1600, S/N HL

R1600, S/N HL

R1600, S/N HL ____________

____________

Project Name ______________________________ Location ___________________________________

Note:

Note: Checklist to be completed by Haskris Approved Service Agent. Checklist MUST be completed for “Full
Load” Start-up to be scheduled.

Directions:

Fax both pages of completed checklist to Haskris (Fax#: 847-956-6595)

Pre Start

Pre Start----Up

Up Checklist:

Checklist:

___

Unit is securely mounted and level.

___

No Refrigeration Service Contactor labels have been affixed to the interior or exterior of the R1600.

___ Clearances for service, ventilation, and access to control panel are adequate per R1600 Instruction Manual.
___ Electrical service to R1600 per table below (Record Inlet Voltage and Branch Circuit Rating):

___

Confirm compressor crankcase heater has been energized for a minimum of 12 hours. (See Section 3.1)

___

Confirm proper phase by verifying the red ‘FAULT’ LED is not lit on phase monitor. (See Section 2.5.1)

___ Hard copper piping with vents/drains as required and properly supported.
___ Vibration Isolators installed at R1600 on both glycol supply and return lines.
___ Separately fused heat trace covered with suitable thickness of closed-cell, UV resistant insulation on all piping

exposed to low ambient temperatures, as required.

___ Supply/Return lines labeled over insulation.
___ 12’ long loop of 1-1/2” reinforced opaque hose between supply and return outlet in equipment room provided.
___ Supply and return ball valves provided at indoor WW4.
___ Supply side temperature (0-100°F) and pressure (0-100psig) gauges provided at indoor heat exchanger.
___ Return side temperature (0-100°F) and flow (10-50gpm) gauges provided at indoor heat exchanger.
___ Leak check performed and no leaks in external piping loop per R1600 Instruction Manual.
___ Preventative Maintenance (PM) Test Kit has been provided to Start-Up Agent.
___ System (50 gallon tank and entire piping loop) is filled with               gallons of glycol/distilled water solution.
___ Reservoir is at tank full level.
___ Lines air purged per R1600 Instruction Manual.
___ Glycol solution             % (Record actual measurement here).
___ Glycol solution pH level             (Record actual measurement here).

___

Spare glycol manufacturer______________________Glycol type__________________________

___ Installer has provided an additional 10 gallons of propylene glycol/distilled water (35% by volume) to top off

system when no-load start-up is performed.

___ Confirm all isolation valves are open and all flush valves are closed.

Note:

Note:       If  any  of  the  above  items  are  found  to  be  deficiencies,  DO  NOT  CONTINUE  WITH  START-UP  and
notify Haskris immediately.  Installer will issue a Credit Card Purchase Order to Haskris Start-Up Agent if any
items  are  found  incomplete  and  resulting  in  delay  of  system start-up.    If  no  deficiencies  are  found,  continue
with Start-Up Checklist below.

--Page 1 of 3—

(continued on next page)

Nominal Power:

Nominal Power: 480V-3Ø-60Hz,+5% / -10% MCA: 54.3A, MOCP 70A

Record Voltage at

Disconnect

(V)

L1-L2

Confirm and Record Size of Time Delay

Breaker (Fusing) Supplying Chiller

(A)

L2-L3