background image

IMPORTANT SAFETy INFORMATION

Form No. mCGm-1113

3

English

ELECTRIC SHOCK HAzARD:

• Plug unit into a properly grounded electrical receptacle

of the correct voltage, size, and plug configuration. If

plug and receptacle do not match, contact a qualified

electrician to determine and install proper voltage and

size electrical receptacle.

• Turn OFF power switch, unplug power cord, and allow

unit  to  cool  before  performing  any  cleaning,

adjustments, or maintenance.

• Unit is not weatherproof. Locate unit indoors where

ambient air temperature is a minimum of 50°F (10°C)

and a maximum of 104°F (40°C).

• DO NOT submerge or saturate with water. Unit is not

waterproof. Do not operate if unit has been submerged

or saturated with water.

• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use jet-

clean spray to clean this unit.

• Do not clean unit when it is energized or hot.
• Do not allow liquids to spill into unit.
• Do not pull unit by power cord.
• Do not allow power cord to hang over edge of counter.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power

cord. Cord must be replaced by Hatco, an Authorized

Hatco  Service  Agent,  or  a  person  with  similar

qualifications.

• This unit must be serviced by qualified personnel only.

Service by unqualified personnel may lead to electric

shock or burn.

• Use  only  Genuine  Hatco  Replacement  Parts  when

service  is  required.  Failure  to  use  Genuine  Hatco

Replacement  Parts  will  void  all  warranties  and  may

subject  operators  of  the  equipment  to  hazardous

electrical voltage, resulting in electrical shock or burn.

Genuine  Hatco  Replacement  Parts  are  specified  to

operate safely in the environments in which they are

used. Some aftermarket or generic replacement parts

do not have the characteristics that will allow them to

operate safely in Hatco equipment.

ExPLOSION  HAzARD:  Do  not  store  or  use  gasoline  or

other flammable vapors or liquids in the vicinity of this or

any other appliance.
Make sure all operators have been instructed on the safe

and proper use of the unit.
This unit is not intended for use by children or persons

with  reduced  physical,  sensory,  or  mental  capabilities.

Ensure proper supervision of children and keep them away

from the unit.
Never leave unit unattended during use.
Do not use unit for any purpose other than for which it is

designed.

WARNING

FIRE HAzARD:

• Locate  unit  a  minimum  of  8″  (200  mm)  from

combustible walls and materials. If safe distances are

not  maintained,  discoloration  or  combustion  could

occur.

• Do  not  obstruct  air  ventilation  openings  on  outer

housing of unit. Unit combustion or malfunction may

occur.

This  unit  has  no  “user-serviceable”  parts.  If  service  is

required on this unit, contact an Authorized Hatco Service

Agent  or  contact  the  Hatco  Service  Department  at 

800-558-0607  or  414-671-6350;  fax  800-690-2966;  or

International fax 414-671-3976.

BURN HAzARD:

• Some  exterior  surfaces  on  unit  will  get  hot.  Avoid

unnecessary contact with unit.

• Do  not  come  in  contact  with  grill  plates  during

operation. Both plates are very hot.

• Allow  unit  to  cool  before  performing  any  cleaning,

adjustments, or maintenance.

Locate  unit  at  proper  counter  height  in  an  area  that  is

convenient for use. Location should be level and strong

enough to support weight of unit and contents.

This  unit  is  designed  for  use  in  environments  where

ambient  temperature  is  between  50°F  (10°C)  and 

104°F (40°C). 
Do  not  locate  unit  in  an  area  subject  to  excessive

temperatures or grease from grills, fryers, etc. Excessive

temperatures and grease could cause damage to unit.
Unit is recommended for use in or on metallic countertops.

For other surfaces, verify with manufacturer that material is

suitable for prolonged temperatures up to 200°F (93°C).

Damage  to  any  countertop  material  caused  by  heat

generated  from  Hatco  equipment  is  not  covered  under

Hatco warranty.
For steel surfaces, use non-abrasive cleaners and cloths

only. Abrasive cleaners and cloths could scratch finish of

unit, marring its appearance and making it susceptible to

soil accumulation.
Do  not  use  harsh  chemicals  such  as  bleach,  cleaners

containing bleach, or oven cleaners to clean this unit.
Do not attempt to cool hot grill plates quickly, such as by

immersing in water. Damage to plates will occur.
This unit is intended for commercial use only—NOT for

household use.
Clean  unit  daily  to  avoid  malfunctions  and  maintain

sanitary operation.

CAUTION

NOTICE

WARNING

Read  the  following  important  safety  information  before  using  this  equipment  to  avoid 

serious injury or death and to avoid damage to equipment or property

.

Summary of Contents for MCG10G

























Reviews: