background image

Symptom

Probable Cause

Corrective Action

Light bulb not working.

Light bulb defective.
Power turned OFF.

Replace light bulb.
Turn unit ON.

Food cavity not hot enough.

Temperature control set too low.

Heating element(s) not working.

Temperature control not working

properly.
Air circulating fan not working

properly.

Adjust temperature control to a

higher setting.
Contact Authorized Service Agent

or Hatco for assistance.
Contact Authorized Service Agent

or Hatco for assistance.
Contact Authorized Service Agent

or Hatco for assistance.

Food cavity too hot.

Temperature control set too high.

Temperature control not working

properly.

Adjust temperature control to a

lower setting.
Contact Authorized Service Agent

or Hatco for assistance.

No heat, but light works.

Temperature control set too low.

Heating element(s) not working.

Temperature control not working

properly.

Adjust temperature control to a

higher setting.
Contact Authorized Service Agent

or Hatco for assistance.
Contact Authorized Service Agent

or Hatco for assistance.

No heat and no light.

Unit turned OFF.
Circuit breaker tripped.

Turn unit ON.
Reset circuit breaker. If circuit

breaker continues to trip, contact

Authorized Service Agent or

Hatco for assistance.

TROUBLESHOOTING

This unit must be serviced by qualified

personnel only. Service by unqualified personnel

may lead to electric shock or burn.

ELECTRIC SHOCK HAZARD: Turn the power

switch OFF, unplug the power cord, and allow

the unit to cool before performing any

maintenance or cleaning.

WARNING

WARNING

10

Form No. MDWM-0608

All manuals and user guides at all-guides.com

Summary of Contents for MDW-1X

















Reviews: