background image

PROGRAMMING CONTROLLER

8

Form No. TFC461RM-0108

8. Both upper and lower heat indicators glow. The display

shows

(the time value for how long conveyor

remains stopped). Repeatedly press Up

or Down

arrow key to scroll to desired setting. Holding down an
arrow key will cause the numbers to change rapidly. Time
can be adjusted from zero to 9 minutes 59 seconds.

9. Press the Enter

key to proceed to the next step.

10.Press the program selection key selected in Step 1 to save

all the settings into memory. The display will show

.

NOTE: In the Continuous Run mode, the conveyor advances

in 1/2 second increments.

When the unit reaches

mode, the upper heating elements automatically go

into a programmed idle power setting. (The display will still show

during idle

mode.) The unit remains in IDLE mode until one of the ten program selection keys
are pressed or the unit goes into AUTO-OFF Mode.

NOTE: Begin with an IDLE mode setting of 30% and adjust the program accordingly

to achieve optimum performance.

1. Simultaneously press/hold the Up

arrow key and the Enter

key for

three

seconds

. The display will show the current programmed power value.

2. Repeatedly press Up

or Down

arrow key to

scroll to desired setting. Setting will change by
10% every time a key is pressed.

3. Press the Enter

key to save setting.

5. The lower heat indicator glows and the display reads

(Lower Power Value).

6. Repeatedly press Up

or Down

arrow key to scroll to

desired setting.

7. Press the Enter

key to proceed to the next step.

1. With display showing

, simultaneously press/hold

program selection key (9 or 10) and Enter

key for five

seconds.

2. After 3 seconds, the upper heat indicator glows and the unit

displays

(Upper Power Value).

3. Repeatedly press Up

or Down

arrow key to scroll to

desired setting.

4. Press the Enter

key to proceed to the next step.

KEYS 9 AND 10 (CYCLES CONTINUOUSLY WHEN PRESSED)

IDLE MODE

Summary of Contents for THERMO-FINISHER TFC-461R





















Reviews:

Related manuals for THERMO-FINISHER TFC-461R