background image

IMPORTANT SAFETY INFORMATION

Form No. TFC461RM-0108

1

For safe and proper operation, plug unit
into a properly grounded electrical outlet of
the

correct

voltage,

size,

and

plug

configuration. If the plug and receptacle do
not match, contact a qualified electrician to
determine and install the proper voltage and
size electrical outlet.

To avoid any injury or damage to the unit,
do not pull unit by power cord.

To prevent any injury, discontinue use if
power cord is frayed or worn.

To reduce the risk of fire, the appliance is to
be installed on a non-combustible surface
only. The appliance is to be installed on
floors or counters of non-combustible
construction with non-combustible flooring
and surface finish and with no combustible
material against the underside, or on non-
combustible slabs or arches having no
combustible material against the underside.
Such construction shall in all cases extend
not less than 12″ (305 mm) beyond the
equipment on all sides.

For safe and proper operation, the unit must
be located a reasonable distance from
combustible walls and materials. If safe
distances are not maintained, discoloration
or combustion could occur. Do not locate
unit under shelving or closer than 12″
(305 mm) from the ceiling.

To ensure proper operation and safety,
allow a minimum of 1″ (25 mm) clearance
along the rear of the unit and 2″ (50 mm)
clearance at the feed and discharge sides.

To avoid any injury, turn the power switch
OFF, unplug the unit from the power source,
and allow to cool before performing any
maintenance.

Unit is not waterproof. DO NOT submerge in
water. Do not operate if it has been
submerged in water. Do not steam clean the
interior or flood with water or liquid
solution.

WARNING

Some exterior surfaces on the unit will get
hot. Use caution when touching these areas
to avoid injury.

To avoid electrical shock or personal injury,
do not steam clean or use excessive water
on the unit.

To avoid any injury or damage, the unit
must be serviced by qualified personnel
only.

To avoid any injury or damage to the unit,
turn the power OFF at the fused disconnect
switch/circuit breaker and allow to cool
before performing any maintenance.

If service is required on this unit, contact an
Authorized Hatco Service Agent or contact
the Hatco Service Department at 800-558-
0607 or 414-671-6350; fax 800-690-2966; or
International fax 414-671-3976.

This product has no “user-serviceable”
parts. To avoid damage to the unit or injury
to personnel, use only Authorized Hatco
Service

Agents

and

Genuine

Hatco

Replacement

Parts

when

service

is

required.

Genuine Hatco Replacement Parts are
specified

to

operate

safely

in

the

environments in which they are used. Some
aftermarket or generic replacement parts do
not have the characteristics that will allow
them to operate safely in Hatco equipment.
It is essential to use Genuine Hatco
Replacement Parts when repairing Hatco
equipment. Failure to use Genuine Hatco
Replacement Parts may subject operators
of the equipment to hazardous electrical
voltage, resulting in electrical shock or
burn.

WARNING

IMPORTANT! Read the following important safety information to avoid personal injury or
death, and to avoid damage to the equipment or property.

Summary of Contents for THERMO-FINISHER TFC-461R





















Reviews:

Related manuals for THERMO-FINISHER TFC-461R