Hatco TOAST-QWIK TQ-300, Installation And Operating Manual

TQ-300, TQ-300BA, TQ-700 & TQ-700H-S
MODELS

1. Plug cabinet into an electrical outlet of the correct voltage, size

and plug configuration. See 

SPECIFICATIONS

for details.

2. Turn the Selector Switch, located on the front panel, to “Toast” 

or “Buns

”. 

See  7  .

NOTE:

When toasting buns, bagels or other single sided bread

products, place cut side down and set Selector Switch to the “Bun”
position.

3. Turn the Speed Control to the lightest/fastest position while 

the unit heats up. 

NOTE:

Allow approximately 15 minutes for a warm-up period.

4. After warm-up period, set the Speed Control to medium

position and toast two slices of bread product. Adjust the Speed
Control to the desired amount of browning.

NOTE:

To toast moist products such as English muffins, rye bread 

or whole wheat, slow the conveyor by turning the Speed Control
knob to a slower/darker setting (clockwise).

TQ-700H MODEL

1. Plug cabinet into an electrical outlet of the correct voltage, size

and plug configuration. See 

SPECIFICATIONS

for details.

2. Turn the Selector Switch, located on the front panel, to “Toast” 

or “Buns”. See  8  .

3. Turn the Top Color Control and Bottom Color Control 

to the lightest/fastest position while the unit heats up. 

NOTE:

Allow approximately 15 minutes for a warm-up period.

4. After warm-up period, set the top and bottom Color Controls 

to medium position and toast two slices of bread product.
Adjust the Top and Bottom Color Controls to the desired
amount of browning.

NOTE:

To toast moist products such as English muffins, rye bread 

or whole wheat, slow the conveyor by turning the Speed Control
knob to a slower/darker setting (clockwise). 

TQ-700HBA MODEL

1. Plug cabinet into an electrical outlet of the correct voltage, size

and plug configuration. See 

SPECIFICATIONS

for details.

2. Turn the Selector Switch, located on the front panel, left 

or right to the “On” position

. 

See  9  .

3. Turn the Color Control to the lightest position and Speed

Control to the fastest position while the unit heats up. 

NOTE: 

Allow approximately 15 minutes for a warm-up period.

4. After warm-up period, set the Color Control and Speed Control 

to medium position and toast two bread products. Adjust
controls to the desired amount of browning.

NOTE: 

When toasting buns, bagels or other single sided bread

products place the 

cut side up

.

NOTE:

Set the Color Control on “Standby” during non-peak

periods of use. Heating elements are set at 50% of power 
in the Standby mode.

MAINTENANCE

GENERAL

The Hatco Toast-Qwik Electric Conveyor Toasters are designed for
maximum durability and performance, with minimum maintenance. 

WARNING

To avoid any injury, turn the power switch off, unplug the unit
from the power source and allow to cool before performing 
any maintenance.

CLEANING

WARNING

This appliance is not of jet-proof construction. Do not use 
jet-clean-spray to clean this appliance.

Exterior

To preserve the bright finish of the unit, it is recommended that 
the exterior surfaces be wiped daily with a damp cloth. Stubborn
stains may be removed with a good stainless steel cleaner 
or a non-abrasive cleaner. Hard to reach areas should be cleaned
with a small brush and mild soap.

CAUTION

Abrasive cleaners could scratch the finish of your
Toast-Qwik toaster.

Toast Crumb Tray & Toast Collector Pan

Remove from unit and wash with soap and water, then rinse.

Conveyor Feeder Guide

Press in the two wire spokes and remove guide from unit. Wipe
clean with a soft, damp cloth or soak the guide in a mild solution 
of 227 milliliters ammonia and 3.785 liters of water (1 cup 
and 1 gallon). Re-install guide by aligning wire spokes with holes 
in toaster.

LUBRICATION

The rear motor bearing requires periodic lubrication at 
recommended intervals. 

CAUTION

Failure to lubricate the rear motor bearing as recommended 
will reduce the operating life of the motor and possibly void 
the warranty.

1. Disconnect toaster from the power supply.

2. If being used for rear discharge, remove the collector pan from

the rear of the unit.

3. Remove the toast ramp from the two support pins at the rear 

of the unit and slide the ramp forward.

!

!

9

Form No. TQCEM-1002

OPERATION