background image

closing time and when the warning signal is on, it blinks 3 seconds before starting the

movement.

 

ATTENTION! When the motion signaling function is switched off, the function of signaling

full opening  is  active. When the motion  signaling is on, the signal of full opening  is
disabled.

SIGNALING OF BARRIER MOVEMENT

Hold down the 

SETUP

 button.

      

The 

LED

 will turn on and then turn off.

    

Release the 

SETUP

 button.

The 

LED

 will blink rapidly for 2s.

     

After the flashing is finished, the 

LED

 will

show the status of the function. The lighted

on means active function, and off the

function inactive.

turned on
disabled

To change the state of the function to the

opposite, press the 

SETUP

 button briefly

within 3 seconds.

 

 

After 3s from the last press, the 

LED

 will

flash 3 times. The controller will remember

the settings and return to normal operation.

 

WARNING SIGNALS

The warning signal function consists in flashing the lamp for 3 seconds before activating the 

barrier in the opening or closing direction.

Hold down the 

SETUP

 button.

      

The 

LED

 will turn on, then turn off and on

again.

  

Release the 

SETUP

 button.

The 

LED

 will blink rapidly for 2s.

     

After blinking, the 

LED

 will show the current

status of the function. The lighted on means

active function, and off the function inactive.

turned on

disabled

 

To change the state of the function to the

opposite, press the 

SETUP

 button briefly

within 3 seconds.

 

 

After 3s from the last press, the 

LED

 will

flash 3 times. The controller will remember

the settings and return to normal operation.

 

Summary of Contents for 535Y




























Reviews: