81
IND100129-210
All specifications are subject to change without prior notice!
Specifications - HD 15T22 MMD-xxx-FHxx
High Bright model
SPECIFICATIONS
Note: All specifi cations are subject to change without prior notice!
Please visit www.hatteland-display.com for the latest electronic version.
2/2
• High Quality TFT with LED Backlight Technology
• Sunlight Readable / High Bright (includes Optical Bonding Technology)
• 15.0 inch viewable image size, Aspect Ratio 4:3
• TFT active-matrix liquid crystal panel
Multi-power Supply:
• 115&230VAC - 50/60Hz + 24 VDC
Note: You may connect either AC power or DC power or both. In case both sources
are connected, power will be sourced from the AC input. If AC input is lost, there will
be a uninterrupted switch-over to DC input.
Power Consumption:
• Operating AC/DC: TBDW (max)
A P P R O V A L S & C E R T I F I C A T E S
TFT Technology:
Power Specifications:
These products have been tested / type approved by the following classification societies (*=pending):
IEC 60945 4th (EN 60945:2002)
IACS E10
EU RO MR*
- Mutual Recognition (covers DNV, BV, ABS, GL, NK and LRS certificates)
• Digital separate synchronization
• Composite synchronization
• Synchronization on green
• Auto detects VGA -> XGA, interlaced and non interlaced
• Video Signal
: Analog RGB 0,7Vp-p
: Input Impedance 75 Ohm
Synchronization Range:
• Horizontal
: 31.5 kHz to 91.1 kHz
• Vertical
: 60 Hz* to 85 Hz
* Recommended for optimal picture quality
Resolutions:
• VGA
: 640 x 480 (including 640 x 350)
• SVGA
: 800 x 600 (including 720 x 400)
• XGA
: 1024 x 768*
* Recommended for optimal picture quality
Video Signals:
• Interlaced HDTV, NTSC, PAL and SECAM video
• Composite video
Synchronization:
Supported Signals:
• HD CMB SX2-A1
: 1 x Console Mount Kit. EN60945 Tested
• HD TMB SX2-A1
: 1 x Table Mount Bracket. EN60945 Tested
• HD VED SX2-A1
: 1 x VESA Adapter Kit (75/75, 100/100 & 200/100mm)
Not EN60945 Tested
• JH 15TAP STD-C1 : 1 x Frame Adapter (15" Series 1 to Series X) retrofit
• HD REM SX1-A1
: 1 x External Remote Control, EN60945 Tested
• HD 15COV SX1-A1 : 1 x UV Sun Cover
• P006997-1
: 1 x IP66 Mount Gasket (EPDM), for Flush/Console mount
Please see user manual/datasheet for more information
Available Accessories:
• W:356.00 [14.02''] x H:307.00 [12.09''] x D:78.50 [3.09''] mm [inch]
• Weight: 5.6kg / 12.3lbs
• Delivery includes an EPDM sealing gasket for IP66 console mount.
Physical Considerations:
Behind front bezel - Glass Display Control™ (GDC) IP66:
• Power On/Off, On Screen Display Menu, Brightness Control (-/+)
• Hotkeys (left/right), Mode Status Indicators (Service)
• Buzzer (through glass), Light Sensor (behind glass)
• Projected Capacitive Touch Screen (Multitouch, USB, Pen/Glove supported)
User Controls:
Factory Options:
• Operating
: Temperature -15 deg. C to +55 deg. C
• Storage
: Temperature -30 deg. C to +70 deg. C
• Humidity
: Up to 95%
• IP Rating
: Protection: IP66 front – IP22 rear (EN60529)
• Compass Safe Dist. : Standard: 100cm - Steering: 65cm
Lifetime Considerations:
Even although the test conditions for bridge units provide for a maximum
operating temperature of 55°C, continuous operation of all electronic
components should, if possible, take place at ambient temperatures of only
25°C. This is a necessary prerequisite for long life and low service costs.
Environmental Considerations:
• DVI-I IN
: 2 x 29p DVI Female (or as VGA IN with adapter)*
• DP1.2 IN
: 1 x 20p DisplayPort (female)
• Comp. Video IN
: 2 x BNC Connector (female)
• SCOM RS-422/485 : 2 x 5-pin Terminal Block 3.81, non-iBuzzer
• VGA OUT
: 1 x 15p HD D-SUB (female) - Clone of VGA IN**
• SCOM+Touch
: 1 x USB TYPE A Connector (female)
• Ethernet
: 1 x RJ45 Connector for Remote Control
• SCOM RS-232
: 1 x 9p D-SUB (female) non-iBuzzer
• Potmeter/User
: 1 x 9p D-SUB (male)
(Potentiometer IN, +5VDC OUT, BRT +/- IN)
• AC Power IN
: 1 x Std IEC Inlet
• DC Power IN
: 1 x 2-pin Terminal Block 5.08
* DVI-I Port #1 as VGA IN also acts as clone to VGA Signal Out (buffered).
**Tested at recommended resolutions. The VGA output signal (buffered) is at same
resolution and sync as the VGA input. The output is working even if the display unit is
turned off, but power cable/supply must be connected/provided.
Signal Terminals:
• Native Resolution
: 1024 x 768
• Pixel Pitch (RGB)
: 0.297 (H) x 0.297 (V) mm
• Response Time
: 19ms (typical), black to white
• Contrast Ratio
: 800:1 (typical)
• Light Intensity
: 800 cd/m² (typical)
• Viewable Angle
: +/- 80 deg. (D/L/R), +/- 60 deg. (U) (typ)
• Active Display Area
: 304.1 (H) x 228.1 (V) mm
• Max Colors
: 16.7 million
TFT Characteristics:
Summary of Contents for HD 15T22 MMD-xxx-F series
