89
IND100129-199
All specifications are subject to change without prior notice!
Specifications - HD 27T22 MMD-xxx-Fxxx
SPECIFICATIONS
Note: All specifi cations are subject to change without prior notice!
Please visit www.hatteland-display.com for the latest electronic version.
2/2
A P P R O V A L S & C E R T I F I C A T E S
These products have been tested / type approved by the following classification societies:
IEC 60945 4th (EN 60945:2002)
IACS E10
EU RO MR
- Mutual Recognition (covers DNV, BV, ABS, GL, NK and LRS certificates)
• W:650.00 [25.59''] x H:437.00 [17.20''] x D:69.50 [2.74''] mm [inch]
• Weight: Approx. 12.0kg / 26.4lbs
Multi-power Supply:
• 115&230VAC - 50/60Hz + 24 VDC
Note: You may connect either AC power or DC power or both. In case both sources
are connected, power will be sourced from the AC input. If AC input is lost, there will
be a uninterrupted switch-over to DC input.
Power Consumption:
• Operating AC/DC: 44W (max)
Physical Considerations:
Power Specifications:
• Digital separate synchronization
• Composite synchronization
• Synchronization on green
• Auto detects VGA -> FHD, interlaced and non interlaced
• Video Signal
: Analog RGB 0,7Vp-p
: Input Impedance 75 Ohm
Synchronization Range:
• Horizontal
: 31.5 kHz to 91.1 kHz
• Vertical
: 60 Hz* to 85 Hz
* Recommended for optimal picture quality
Resolutions:
• VGA
: 640 x 480 (including 640 x 350)
• SVGA
: 800 x 600 (including 720 x 400)
• XGA
: 1024 x 768
• SXGA
: 1280 x 1024
• UXGA
: 1600 x 1200
• FHD
: 1920 x 1080*
* Recommended for optimal picture quality
Video Signals:
• Interlaced HDTV, NTSC, PAL and SECAM video
• Composite video
Synchronization:
Supported Signals:
Behind front bezel - Glass Display Control™ (GDC) IP66:
• Power On/Off, On Screen Display Menu, Brightness Control (-/+)
• Hotkeys (left/right), Mode Status Indicators (ECDIS, Service)
• Buzzer (through glass), Light Sensor (behind glass)
• Projected Capacitive Touch Screen (Multitouch, USB, Pen/Glove supported)
• Optical Bonding Technology
• Color Calibrated models (ECDIS)
User Controls:
Factory Options:
• HD CMB SX2-E1
: 1 x Console Mount Kit. EN60945 Tested
• HD TMB SX1-C1
: 1 x Table Mount Bracket. EN60945 Tested
• HD VED SX2-H1
: 1 x VESA Adapter (75/75, 100/100 & 200/100mm)
Not EN60945 Tested
• HD REM SX1-A1
: 1 x External Remote Control, EN60945 Tested
• HD 27COV SX1-A1 : 1 x UV Sun Cover
• P018743
: 1 x IP66 Mount Gasket (EPDM), for Flush/Console mount
Please see user manual/datasheet for more information
Available Accessories:
• LED Backlight Technology, Color Active Matrix
• 27.0 inch viewable image size, Widescreen, Aspect Ratio 16:9
• a-SI (amorphous silicon) Thin Film Transistor (TFT)
• Native Resolution
: 1920 x 1080 (FHD)
• Pixel Pitch (RGB)
: 0.31125 (H) x 0.31125 (V) mm
• Response Time
: 12 ms (typical) (on/off)
• Contrast Ratio
: 3000:1 (typical)
• Light Intensity
: 300 cd/m² (typical)
• Viewable Angle
: +/- 89 deg. (typical) (Up/Down/Left/Right)
• Active Display Area
: 597.6 (H) x 336.15 (V) mm
• Max Colors
: 16.7 million
TFT Technology:
TFT Characteristics:
• Operating
: Temperature -15 deg. C to +55 deg. C
• Storage
: Temperature -30 deg. C to +70 deg. C
• Humidity
: Up to 95%
• IP Rating
: Protection: IP66 front – IP22 rear (EN60529)
• Compass Safe Dist. : Standard: 190cm - Steering: 110cm
Lifetime Considerations:
Even although the test conditions for bridge units provide for a maximum
operating temperature of 55°C, continuous operation of all electronic
components should, if possible, take place at ambient temperatures of only
25°C. This is a necessary prerequisite for long life and low service costs.
Environmental Considerations:
• DVI-I IN
: 2 x 29p DVI Female (or as VGA IN with adapter)*
• DP1.2 IN
: 1 x 20p DisplayPort (female)
• Comp. Video IN
: 2 x BNC Connector (female)
• SCOM RS-422/485 : 2 x 5-pin Terminal Block 3.81, non-iBuzzer
• VGA OUT
: 1 x 15p HD D-SUB (female) - Clone of VGA IN**
• SCOM+Touch
: 1 x USB TYPE A Connector (female)
• Ethernet
: 1 x RJ45 Connector for Remote Control
• SCOM RS-232
: 1 x 9p D-SUB (female) non-iBuzzer
• Potmeter/User
: 1 x 9p D-SUB (male)
(Potentiometer IN, +5VDC OUT, BRT +/- IN)
• AC Power IN
: 1 x Std IEC Inlet
• DC Power IN
: 1 x 2-pin Terminal Block 5.08
* DVI-I Port #1 as VGA IN also acts as clone to VGA Signal Out (buffered).
**Tested at recommended resolutions. The VGA output signal (buffered) is at same
resolution and sync as the VGA input. The output is working even if the display unit is
turned off, but power cable/supply must be connected/provided.
Signal Terminals:
Summary of Contents for HD 15T22 MMD-xxx-F series
