Hatteland HT 216, User Manual User Manual

34

IND100241-2

INB100084-1 (Rev 14)

Appendix

Pin Assignments - 5P PS/2 MOUSE

Pin 1: Mouse Data

Pin 3: Ground

Pin 5: Mouse Clock

Pin 2: Not Connected

Pin 4: Vcc +5V

Pin 6: Not Connected

Pin Assignments - USB TYPE A

Pin 2: Negative Data

Pin 1: VCC +5V

Pin 3: Positive Data

Pin 4: Ground

Pin Assignments - RJ45 10/100 LAN

Use category 5 - twisted pair cable

1  2  3  4  5  6  7  8

Pin 01 - TDP

Transmit Differential Pair (Positive)

Pin 02 - TDN

Transmit Differential Pair (Negative)

Pin 03 - RDP

Receive Differential Pair (Positive)

Pin 04 - NC

Not Connected

Pin 05 - NC

Not Connected

Pin 06 - RDN

Receive Differential Pair (Negative)

Pin 07 - NC

Not Connected

Pin 08 - NC

Not Connected

Pin Assignments - 9P Serial COM RS-232

This connector is commonly used for:

5    4   3   2   1

9   8   7   6

Pin 01 - DCD

Data Carry Detect

Pin 02 - SIN

Serial In or Receive Data

Pin 03 - SOUT Serial Out or Transmit Data

Pin 04 - DTR

Data Terminal Ready

Pin 05 - GND Ground

Pin 06 - DSR

Data Set Ready

Pin 07 - RTS

Request To Send

Pin 08 - CTS

Clear To Send

Pin 09 - RI

Ring Indicate

Pinout Assignments - Common Connectors

Pin Assignments - RJ45 10/100/1000 GBLAN

Pin 01 - D0P

Differential Pair 0 (Positive)

Pin 02 - D0N

Differential Pair 0 (Negative)

Pin 03 - D1P

Differential Pair 1 (Positive)

Pin 04 - D2P

Differential Pair 2 (Positive)

Pin 05 - D2N

Differential Pair 2 (Negative)

Pin 06 - D1N

Differential Pair 1 (Negative)

Pin 07 - D3P

Differential Pair 3 (Positive)

Pin 08 - D3N

Differential Pair 3 (Negative)

1  2  3  4  5  6  7  8

Note:

 Not all connectors may be available on your specific product. This depends on the amount of additional hardware installed from factory, 

or customized solutions. These pin assignments are for the common connectors used. 

Connectors are seen from users Point Of View (POV).

Pin Assignments - 15P HD RGB VGA

Pin 01

Red, analog

Pin 02

Green, analog

Pin 03

Blue, analog

Pin 04

Reserved for monitor ID bit 2 (grounded)

Pin 05

Digital ground

Pin 06

Analog ground red

Pin 07

Analog ground green

Pin 08

Analog ground blue

Pin 09

+5V power supply for DDC (optional)

Pin 10

Digital ground

Pin 11

Reserved for monitor ID bit 0 (grounded)

Pin 12

DDC serial data

Pin 13

Horizontal sync or composite sync, input

Pin 14

Vertical sync, input

Pin 15

DDC serial clock

5    4   3   2   1

15   14   13   12   11

10   9   8   7   6

Pin Assignments - 5P PS/2 KEYBOARD

Pin 1: Keyboard Data

Pin 3: Ground

Pin 5: Keyboard Clock

Pin 2: Not Connected

Pin 4: Vcc +5V

Pin 6: Not Connected

Pin Ass. - 5P PS/2 KMOUSE Combined

Pin 1: Keyboard Data

Pin 3: Ground

Pin 5: Keyboard Clock

Pin 2: Mouse Data

Pin 4: Vcc +5V

Pin 6: Mouse Clock

Pin Assignments - USB TYPE B

Pin 2: Negative Data

Pin 3: Positive Data

Pin 4: Ground

Pin 1: VCC +5V

Pin Assignments - FIREWIRE IEEE-1394

Pin 01 - VCC

Power

Pin 02 - GND Grounding for power and inner cable shield

Pin 03 - TPB- Twisted Pair B-   Receive Strobe, Transmit Data

Pin 04 - TPB+ Twisted Pair B+  Receive Strobe, Transmit Data

Pin 05 - TPA- Twisted Pair A-   Transmit Strobe, Receive Data

Pin 06 - TPA+ Twisted Pair A+  Transmit Strobe, Receive Data

1

3

5

2

4

6

Pin Assignments - 5P S-VHS/S-VIDEO

Pin 1: Ground (Y)

Pin 3: Y - Intensity (luminance)

Pin 2: Ground (C)

Pin 4: C - Color (chrominance)

Pin Assignments - RCA/BNC 1P COMP. VIDEO

 Ground Shield

Pin 1: Video Signal

Note: The table above lists commonly-used RS-232 signals and pin 

assignments, however Serial Communication for Hatteland Display products 

may vary from product to product to support different end user systems. 

Please check additional pin assignments section in this manual for specific 

RS-232/RS-422/RS-485 pin assignments for your exact product.