108
4000014930
E10.16
USA / GB
H12/15/18 SX/SXL - HS 3388/4388/5388 RT/RTXL - COMPACT 10/12 DX - COMPACT 2668/3368 RT
C
- Maintenance
Second test : On ramp :
• On non slipping loading ramp (maximum slope 20 %).
• Draw a line on the slope to create a stopping reference.
• Climb on the ramp at microspeed.
• Release the joystick when the front wheels make contact with the stopping line previously drawn.
• When the machine comes to a stop, measure the distance between the middle of the front wheels and
the reference mark on the ground :
• If the distance is lower than 0,5 m(1 ft8 in) : the test validates correct operation.
• If the machine goes down again (skids, slips) of a distance higher than 0,5 m(1 ft8 in) :
Contact HAULOTTE Services® to repair the system.
3.3.3 - Hydraulics
3.3.3.1 - Oil replacement
Replace oil after each major intervention, and each time an anomaly has been detected.
Take an oil sample each year, check the viscosity, ensure there are no foreign bodies and
change if necessary. Systematically change the oil in the hydraulic circuit every 2 years.
• Only use oils that that match the technical characteristics that correspond to HAULOTTE®
recommendations (
Section B 1 - Lubrication diagram - List of ingredients) or
contact HAULOTTE Services®.
• Do not mix two oils with different characteristics : If necessary, drain and clean the whole system.
• Check the cleanliness of the oil filter cartridge (no metal shavings, rubber, plastic, …) : If necessary,
drain and clean the whole system.
• Respect the following step during filling :
• The machine must be completely stowed (For machines fitted with : Stabilisers raised).
• Fill the tank.
• 1 : Perform a complete cycle (fully extend and retract) of each cylinder.
• 2 : Fill the tank if necessary(Never above of the maximum level).
• Repeat the step ( 1 ) and ( 2 ) for each cylinder on the machine.
Summary of Contents for Compact 10DX
