29
2420344510 E
11.11
AUS
Telescopic handlers
C
- Pre-operation and controls
1.
Jib cylinders: lifting and telescopic action cylinders, compensation output, compensation input
(crowding) and cases :
• Pins secure, hydraulic hoses in good condition, no leaks.
• Check the state of the extension booms wear pads.
2.
Left-hand stabiliser and detector : Pins secure, hydraulic hoses in good condition, no leaks (on
HTL4010 and HTL3210 only).
3.
Front axle : Steering cylinders in good condition, no leaks; joint pins and flanges secured tightly,
hydraulic hoses in good condition, no leaks.
4.
Wheel/Tyre assembly : No loose or missing wheel nuts, inflated correctly. Check the state of the
tyres and their level of wear.
5.
Front headlights : Clean, in good condition and working properly.
6.
Mirrors : Clean, in good condition and working properly.
7.
Fuel tank : Check the fuel level, top up as required, the filler cap is securely fastened. Check for
any leaks on the fuel tank..
8.
Front work lights (optional) : Clean, in good condition and working properly.
9.
Cab and electrical circuit :
• The cab is an approved protective cab in accordance with FOPS and ROPS standards:
Check the FOPS/ROPS label in the cab.
• Check alarms: eg. engage the reverse drive and sound the horn.
• General appearance, no visible damage, capacity charts and Operator & Safety ma-
nual located in the manual holder.
• Window glass in good condition and clean.
• Gauges, switches, joystick, parking brake pedals and horn all operational.
• Check the seat belt for damage, replace it if it is frayed or the webbing is cut, the buc-
kles are damaged or the mounting hardware is loose or damaged.
• Check that the applicable load and capacity charts are installed in the cab..
10.
Hydraulic oil tank : Recommended fluid level on the level gauge (the oil must be cold) ; filler/brea-
ther cap securely in place and in working order. Check for hydraulic leaks around the reservoir.
11.
Rear work lights (optional) : Clean, in good condition and working properly.
12.
Wheel/Tyre assembly : No loose or missing wheel nuts, inflated correctly. Check the state of the
tyres and their level of wear.
13.
Rear axle : Steering cylinders in good condition, no leaks, pivot pins secure, hydraulic hoses in
good condition, no leaks.
14.
Left axle locking cylinder (Option) : Cylinders in good condition, no leaks and securely fastened.
15.
Stop and reverse lights : Clean, in good condition and working properly.
16.
Right axle locking cylinder(Option) : Cylinders in good condition, no leaks and securely fastened.
17.
Wheel/Tyre assembly : No loose or missing wheel nuts, inflated correctly. Check the state of the
tyres and their level of wear.
18.
Engine compartment :
• Engine crankcase and radiator : Check the levels and top up as required. Check that
the radiator is clean.
• Drive belt : check their condition, adjust and/or replace as required.
• Air filter blockage indicator : Check if it is clogged. Replace the element as required.
• Open the engine cover under the cab and check the battery cables : They are secure
and that there is no visible damage or corrosion.
• Engine canopy properly secured and locked.
19.
Mirrors : Clean, in good condition and working properly.
20.
Wheel/Tyre assembly : No loose or missing wheel nuts, inflated correctly. Check the state of the
tyres and their level of wear.
Summary of Contents for HTL 3210
