54
4000414930
E 10.15
USA / GB
General data
Pins and bearing inspection
MS0002
3 - Control and maintenance
The control of pins, stop pins, bushes and bearing must be carried out according to the following recommendations :
• Every day before use : Fast visual inspection without disassembling.
• Check the presence of the pins and visible stops pins without disassembling.
• Check the presence of the screws.
• Check absence of deformations, cracks or breakage of pins and/or stops pins.
• Check absence of heavy abrasion, wear or oxidation of the pins, stops pins.
• All 250 h or 6 months : Reinforced visual inspection with disassembling of certain elements to reach the bushes or
bearing. In addition to the above cited criteria, verify the following :
• Check the presence and the position of the bushes and bearings.
• Check the absence of shaving in periphery of the pins.
• Check the absence of heavy abrasion, wear or oxidation of the bushes and bearing.
• Check the absence of deformations, cracks or breakage of the bushes and bearing.
• Check the absence of radial gap > 0,5 mm (19690 µ in) on the pins.
• Every 5 years : Complete disassembling of the pins, bushes and bearing. In complement of the inspections above
cited, it is necessary to check :
• For the stages :
• Check the presence of material of friction.
• For the bearings :
• After disassembling, protect the bearing from pollution and shocks.
• Clean the bearing with a suitable solvent.
• Check the absence of shaving in the housing of the bearing and/or the bearing.
• Check the absence of heavy abrasion, wear, oxidation, deformations of the balls (or rollers) and the
ball races.
The periodicity can evolve under the following conditions :
• Abnormal noise during movements of the structure.
• Prolonged storage of the machine ( 6 months).
• Specific storage and use Environment (strong moisture and salinity of the air).
4 - Criteria of replacement
The pins, stop pins, bushes and bearing must be replaced as soon as one of the anomalies quoted above is noted.
Bearing and bushes must be imperatively changed at the end of 10 years of use.
Summary of Contents for STAR 10
