background image

rev. 122817MH

 

©2017 HAUSMANN INDUSTRIES, INC.

 

 

Warranty Statement

 

 

Hausmann Industries, Inc. will warrant parts for this table against defects in manufacture for a period of three 
years from the date of purchase.

 

 

Upholstery, cables are excluded from this warranty.

 

 

Providing

 

The table has not been serviced by person not authorized by Hausmann Industries, Inc. and has not been 
misused or tampered with and has been used on the correct voltage as branded on it.

 

 

This Warranty Excludes:

 

Parts of this table the failure of which, in the opinion of the dealer or manufacturer, is a result of misuse or 
abuse or any other reason not directly attributed to a fault in manufacture.

 

 

In the Event of Failure:

 

If authorized by your Hausmann dealer or Hausmann Industries, Inc., the complete table should be returned to 
the dealer from which it was purchased or to the nearest authorized service agent, together with a full report, 
freight paid and insured.

 

 

Under No Circumstances

 

Shall Hausmann Industries, Inc. or their agents or dealers be liable in any manner whatsoever for any 
compensation or damages to any person occasioned by this table for any loss, injury or any damage 
occasioned by or as a result of misuse or abuse of this table. Hausmann Industries, Inc. or their agents or 
dealers shall not be liable for any losses, financial or otherwise, suffered as a consequence of any failure of the 
table which is rectified under the terms of this warranty agreement.

 

 

Loss in Transit:

 

The warrantor does not accept any responsibility for loss or damage to the table in transit.

 

Any express or applied conditions, statements of warranty, statutory or otherwise (save specifically provided 
above) is hereby excluded.

 

 

Acceptance of this agreement

 

Is indicated by the purchaser taking possession of this table and putting it to use.

 

 

 

 
 
 
 
 
 
 
 
 
 
 

 
 

3

 

 

 

Summary of Contents for 6058











Reviews: