Haussmann 5959003, Operator'S Manual

17

The required torque can be preselected in 20 settings with 

the torque preselection ring (3). With the correct setting, the

insert bit is stopped as soon as the screw is screwed flush 

into the material or when the set torque is reached.

Select a higher setting when driving out screws, or set to 

the symbol “Drilling”.

The safety clutch is deactivated in the “Drilling” position.

The 3 LEDs of the battery charge-control indicator (9) flash 

rapidly when the battery temperature is not within the 

operating temperature range of -10º to +70

O

C (14ºF to 

158ºF).

Setting the Torque

Gear Selection, Mechanical

Adjusting the Speed

Fully automatic spindle locking(Auto-lock)

Run-on Brake

Battery charge-control Indication

Gear 1:

Actuate the gear selector (4) only when the tool is 

at a standstill.

Two speed ranges can be used with the gear selector (4).

Temperature Dependent Overload Protection

When used as directed, the power tool cannot be subject 

to overload. When the load is too high or the allowable 

battery temperature of 70

O

C (158ºF) is exceeded, the 

electronic control switches off the power tool until the 

temperature is in the optimum temperature range again.

The 3 LEDs of the battery charge-control indicator (9) 

flash rapidly when the battery temperature is not within

the operting temperature range of -10 to +70

O

C (14ºF to 

158ºF) and/or when the overload protection has actuated.

Protection Against Deep Discharging

Operating Instructions

The Li-ion battery is protected against deep discharging 

by the “Electronic Cell Protection (ECP)”. When the battery 

is empty, the tool is switched off by a protective circuit: 

the inserted bit no longer rotates.

Apply the power tool to the screw only when it is switched 

off. Rotating tool inserts can slip off.

Soft Grip

The gripping surface (soft grip) (5) reduces the danger of 

slipping and thereby improves the grip and handling of 

the tool.

At the same time, the rubber coating provides a 

vibration-reducing effect for increased comfort for the 

operator.

Tips

Cleaning and Maintenance

After longer periods of working at low speed, allow the 

drill to cool down by running it for approx. 3 minutes at 

maximum speed with no load.

For drilling in metal, use only perfectly sharpened HSS 

(high-speed steel) drill bits. 

Before screwing larger, longer screws into hard materials, 

it is advisable to predrill a pilot hole with the core diameter 

of the thread to approx. 2/3 of the screw length.

Place the direction of rotation direction switch (7) into the 

middle position before carrying out any tasks on the tool,

e.g. changing bits or maintenance, or before transporting 

or storing the tool. Accidental operation of the On/Off 

switch (8) may result in injury.

Always pull the battery charger (12) out of the mains 

socket and remove the battery pack before you clean or 

maintain the device.

The cordless drill/driver is maintenance-free.
1)    Always keep the tool clean, dry and free of oil or 

       grease.

Low speed range (0-400 RPM); for screwdriving or 

working with a large drilling diameter.

Gear 2:

High speed range (0-1300 RPM); for working with a small 

drilling diameter. If the gear selector (4) cannot be fully 

engaged, lightly rotate the driver spindle with the drill bit 

by twisting the drill chuck.

The speed of the switched on power tool can be variably 

adjusted, depending on how far the On/Off switch (8) is 

pressed.

Light pressure on the On/Off switch (8) results in a low 

rotational speed. Further pressure on the switch results 

in an increase in speed. 

When the On/Off switch (8) is not pressed, the drill spindle 

and thus the tool holder are locked.

This enables screws to be screwed in, even when the 

battery is empty and allows for the tool to be used  as a 

screwdriver.

When the On/Off switch (8) is released, the chuck brakes 

to a stop, thus preventing the run-on of the tool.

When driving in screws, wait until the screw is screwed in 

flush with the material and then release the On/Off switch 

8. By doing so, the head of the screw does not penetrate 

into the material.

The battery charge-control indicator (9) consists of three

green LEDs, and indicates the charge condition of the 

battery for a few seconds when the On/Off switch (8) is

pressed halfway or fully.

LED

Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Slow flashing 1 x green

Capacity

≥66%
34-66%
11-33%
≤11%

CAUTION!



!