27
DESCRIPTION, SPECIFICATIONS AND INSTRUCTIONS
Description of symbols
The rating plate on your tool may show symbols.
These represent important information about
the product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Tool is listed by Underwriters Labo-
ratories and listed to Canadian Stan-
dards by Underwriters Laboratories
Environmental protection
Recycle unwanted materials instead
of disposing of them as waste. All
tools, hoses and packaging should be
sorted, taken to the local recycling centre and
disposed of in an environmentally safe way.
SMS 15A-10‘-DB
Voltage
120V ~ 60Hz
Input current
15 Amp
No load speed
4500 RPM
Rated power
1800 W
Blade size Ø10“ x Ø5/8“
0
4
h
t
e
e
t
f
o
r
e
b
m
u
N
Max cutting depth (90°)
Max cutting depth (45°)
0° Mitre / 0° Bevel
45° Mitre / 0° Bevel
0° Mitre / 45° Bevel
45° Mitre / 45° Bevel
45°R Mitre / 45°R Bevel
SMS 15A-12‘-DB
Voltage
120V ~ 60Hz
Input current
15 Amp
No load speed
4500 RPM
Rated power
1800 W
Blade size Ø12“ x Ø1“
0
4
h
t
e
e
t
f
o
r
e
b
m
u
N
Max cutting depth (90°)
Max cutting depth (45°)
0° Mitre / 0° Bevel
45° Mitre / 0° Bevel
0° Mitre / 45° Bevel
45° Mitre / 45° Bevel
45°R Mitre / 45°R Bevel
Safety instructions
Safety rules for laser lights
WARNING.
Do not stare directly at the laser beam.
WARNING.
It may be more difficult to see the
laser line in conditions of bright sunshine and on
certain surfaces
A hazard may exist if you deliberately stare into
the beam, please observe all safety rules as
follows;
The laser shall be used and maintained in ac-
cordance with the manufacturer’s instructions.
Never aim the beam at any person or an object
other than the workpiece.
The laser beam shall not be deliberately aimed
at personnel and shall be prevented from
being directed towards the eye of a person for
longer than 0.25s.
Always ensure the laser beam is aimed at a
sturdy workpiece without reflective surfaces.
I.e. wood or rough coated surfaces are accep-
table. Bright reflective sheet steel or the like
is not suitable for laser use as the reflective
surface could direct the beam back at the
operator.
Do not change the laser light assembly with a
different type. Repairs must be carried out by
the laser manufacturer or an authorized agent.
CAUTION.
Use of controls or adjustments or
performance of procedures other than those
specified herein may result in hazardous radiati-
on exposure.
UL
®
C
US
EN
3 5/32“ (8 cm)
1 9/16“ (4 cm)
13 3/8x3 5/32“ (34x8 cm)
9 7/16x3 5/32“ (24x8 cm)
13 3/8x3 17/32“ (34x9cm)
13 3/8x2 5/32“ (34x5.5 cm)
9 7/16x3 17/32“ (24x9 cm)
9 7/16x2 5/32“ (24x5.5 cm)
9 7/16x1 1/2“ (24x3.8 cm)
13 3/8x1 9/16“ (34x4 cm)
9 7/16x1 9/16“ (24x4 cm)
9 7/16x1 3/32“ (24x2.8 cm)
3 17/32“ (9 cm)
2 5/32“ (5.5 cm)
RAYONNEMENT LASER – NE PAS REGARDER LE RAYON NI
VISUALISER DIRECTEMENT À L’AIDE D’INSTRUMENTS D’OPTIQUE
LASER RADIATION – DO NOT STARE INTO BEAM OR VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS
Longueur d’onde / Wavelength: 650 nm
Puissance max. / Max Output: ≤ 1 mW
Produit laser de classe II / Class II Laser Product
Conforme aux parties 1040.10 et 1040.11
de la norme FDA21 C FR
Complies with FDA21 CFR Parts 1040.10 and 1040.11
É
VITER L’EXPOSITION – Un rayonnement laser passe par cette ouverture
AVOID EXPOSURE – Laser radiation is emitted through this aperture
CAUTION
AVERTISSEMENT
