manualshive.com logo in svg

Haussmann RFLNS, Installation & Operation Manual

The Haussmann RFLNS Installation & Operation Manual is an essential guide for effortlessly setting up and operating your Haussmann RFLNS product. This comprehensive manual provides step-by-step instructions, ensuring a smooth installation process. Download this manual for free from 88.208.23.73:8080, empowering you to unlock the full potential of your Haussmann RFLNS product.

Share
Download
background image

1-18

 

I

nstallatIon

P/N 0387183_V

U.S. & Canada 1-800-922-1919 • Mexico 1-800-890-2900 • WWW.HUSSMANN.COM

6

 

Move the second merchandiser 
against first, mating alignment 
pins with corresponding holes. 
Use care when pushing the cases 
together.  
 

 

RL / RM / RLN / RMN / 
RLNI: Do not cut wires routed 
along the front bumper retainer. 
See detail in Figure 6. 
 
 

 

The RMTM / RLTM / RMTD 
has no alignment pin and the 
wireway is at the top front.

Figure 5C, Part 2. Apply Gasket to Right End of RLTM / RMTM / RMTD

RLTM

RMTM

RMTD

F

R

O
N

T

Right End

Case-to-Case

Joint or End Panel

Apply Donut Gasket,

Foam Gaskets

and Gasket Pad to

Right End Only

F

R

O
N

T

Left End

Only Use

Donut Gasket on 

left end of 

a Case-to-Case

Joint

If attaching an End

Panel, all 4 Gaskets

must be applied.

Install Donut 

Gasket as Shown

(seat into groove)

Apply Unitized 

Gasket Pad (4)

Unitized Gasket Pad

////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

/     /     /     /     ~/     /     /     /     /     /     /     /     /     /     /     /      /      /      /      /      /      /      /      /      /      /       /       /       /       /       /        /        /       /       /       /       /        /        /        /        /        /        /         /         /        /        /        /        /        /        /        /        /         /         /        /        /       /        /       /        /        /        /         /           /          /          /           /           /            /             /            /        /         /           /         /            /         /        /          /          /           /         /         /         /          /        /          /       /       /

/     /     /     /        ~/     /     /     /     /     /     /     /     /     /     /     /      /      /      /      /    

  /      /      /      /      /      /       /       /       /       /       /        /        /       /       /       /       

/        /        /        /        /        /      

  /         /         /        /        /        /        /        /        /        /        /         /         /        /   

     /       /        /       /        /        /        /         /       

    /          /          /           /           /            /             / 

           /        /         /           /     

    /            /         /        /          /          /           /         /         /         /          /        /      

    /       /       /

///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

Overlap 

Foam Gasket  3

as Shown

/      /      /      /      /      /      /       /

/////////////////////////////

1

2

3

/     /     /     /        /     /     /     /     /     /     /     /     /     /     /     /      /      /      /      /      /      /      /      /      /      /       /       /       /       /       /        /        /       /       /       /       /

        /        /        /        /        /        /         /         /        /        /        /        /        /        /        /        /         /         /        /        /       /        /       /        /        /        /         /        

   /          /          /           /           /            /             /            /        /         /           /         /            /         /        /          /          /           /         /         /         /          /        /       

   /       /       /

////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

/              /                 /                      /    

                    /                         /            

        /                      /                      /   

                      /                          /         

               /                        /                   

          /                         /                      

    /                    /                      /          

               /                         /                 

        /                               /                 

                  /                            /          

                 /                                  /       

                       /                                  /  

                         /                       /        

                 /                /

/                        /                         /                        /                                       /                          /                          

  /                          /                                /                            /                             /                               /                

          /                             /                                    /                                    /                           /                           

       /                              /                                  /                                    /                               /                           

           /                                                                          /

/              /          /                        /                         /                    /                      /           

           /                         /                                         /                                                         

                      /                                                                               /                                   

      /                                                                     /                                              /           

                                       /                                                                             /                  

                 ~     /                                                       /                                        /

/      /      /      /      /      /      /       /

/////////////////////////////

1
2
3

Donut Gasket

Foam 1 inch x 1/2 inch

Foam 1/2 inch x 1/4 inch

Install Donut 

Gasket as Shown

/////////////////////////////

Install Donut 

Gasket 

(seat into groove)

Install Donut 

Gasket 

(seat into groove)

///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

Gasket 3

must overlap

Gasket 3

/      /      /      /      /      /      /       /

/////////////////////////////

Detail A

Detail B

Gasket 3
must overlap at all intersections
 — Do not butt gaskets. 

1

2

3

2

Detail C

Only Foam Gasket

Number 3 

/      /      /      /      /      /      /       

/////////////////////////////

2

3

/////////////////////////////

Detail D

1

F

R

O
N

T

Right End

Case-to-Case

Joint or End Panel

Apply Donut Gasket,

Foam Gaskets

and Gasket Pad to

Right End Only

F

R

O
N

T

Left End

Only Use

Donut Gasket on 

left end of 

a Case-to-Case

Joint

If attaching an End

Panel, all 4 Gaskets

must be applied.

Install Donut 

Gasket as Shown

(seat into groove)

Apply Unitized 

Gasket Pad (4)

Unitized Gasket Pad

////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

/     /     /     /     ~/     /     /     /     /     /     /     /     /     /     /     /      /      /      /      /      /      /      /      /      /      /       /       /       /       /       /        /        /       /       /       /       /        /        /        /        /        /        /         /         /        /        /        /        /        /        /        /        /         /         /        /        /       /        /       /        /        /        /         /           /          /          /           /           /            /             /            /        /         /           /         /            /         /        /          /          /           /         /         /         /          /        /          /       /       /

/     /     /     /        ~/     /     /     /     /     /     /     /     /     /     /     /      /      /      /      /    

  /      /      /      /      /      /       /       /       /       /       /        /        /       /       /       /       

/        /        /        /        /        /        /         /         /        /        /        /        /        /       

 /        /        /         /         /        /   

     /       /        /       /        /        /        /         /       

    /          /          /           /           /            /             /            /        /         /           /     

    /            /         /        /          /          /           /         /         /         /          /        /      

    /       /       /

///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

Overlap 

Foam Gasket  3

as Shown

/      /      /      /      /      /      /       /

/////////////////////////////

1

2

3

/     /     /     /        /     /     /     /     /     /     /     /     /     /     /     /      /      /      /      /      /      /      /      /      /      /       /       /       /       /       /        /        /       /       /       /       /

        /        /        /        /        /        /         /         /        /        /        /        /        /        /        /        /         /         /        /        /       /        /       /        /        /        /         /        

   /          /          /           /           /            /             /            /        /         /           /         /            /         /        /          /          /           /         /         /         /          /        /       

   /       /       /

////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

/              /                 /                      /   

                     /                         /          

          /                      /                      /

                         /                          /    

                    /                        /             

                /                         /               

           /                    /                      /    

                     /                         /         

                /                               /         

                          /                            /  

                         /                                 

 /                              /                        

          /                           /                   

    /                         /                /

/                        /                         /                        /                                       /                          /                          

  /                          /                                /                            /                             /                               /                

          /                             /                                    /                                    /                           /                            

      /                              /                                  /                                    /                               /                             

         /                                                                          /

/              /          /                        /                         /                    /                      /        

              /                         /                                         /                                                    

                           /                                                                               /                             

            /                                                                     /                                              /     

                                             /                                                                             /           

                        ~     /                                                       /                                        /

/      /      /      /      /      /      /       /

/////////////////////////////

1
2
3

Donut Gasket

Foam 1 inch x 1/2 inch

Foam 1/2 inch x 1/4 inch

Install Donut 

Gasket as Shown

/////////////////////////////

Install Donut 

Gasket 

(seat into groove)

Install Donut 

Gasket 

(seat into groove)

///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

Gasket 3

must overlap

Gasket 3

/      /      /      /      /      /      /       /

/////////////////////////////

Detail A

Detail B

Gasket 3
must overlap at all intersections
 — Do not butt gaskets. 

1

2

3

2

Detail C

Only Foam Gasket

Number 3 

/      /      /      /      /      /      /       

/////////////////////////////

2

3

/////////////////////////////

Detail D

1

Right End Case

Permit Number:

20-05195

Summary of Contents for RFLNS

































































Reviews:

No comments

Related manuals for RFLNS

APW Wyott Racer DMXD-30H Specifications preview
Racer DMXD-30H
Brand: APW Wyott Pages: 2
Hussmann RI2N Technical Data Sheet preview
RI2N
Brand: Hussmann Pages: 6
Hussmann Impact C2SLE Datasheet preview
Impact C2SLE
Brand: Hussmann Pages: 8
Star Manufacturing Hot Food Merchandisers 12MC Specification Sheet preview
Hot Food Merchandisers 12MC
Brand: Star Manufacturing Pages: 2
ChefLine CHVN1350 Instruction Manual preview
CHVN1350
Brand: ChefLine Pages: 98
Hussmann Impact Excel M5EP Datasheet preview
Impact Excel M5EP
Brand: Hussmann Pages: 6

Brands by name

Popular brands

Load more brands