manualshive.com logo in svg

Haussmann RFLNS, Installation & Operation Manual

The Haussmann RFLNS Installation & Operation Manual is an essential guide for effortlessly setting up and operating your Haussmann RFLNS product. This comprehensive manual provides step-by-step instructions, ensuring a smooth installation process. Download this manual for free from 88.208.23.73:8080, empowering you to unlock the full potential of your Haussmann RFLNS product.

Share
Download
background image

P/N 0387183_V 

IMPORTANT

KEEP IN STORE FOR FUTURE REFERENCE

Quality that sets industry standards!

This merchandiser is NSF

®

 certified.

12999 St. Charles Rock Road • Bridgeton, MO 63044-2483 

U.S. & Canada 1-800-922-1919 • Mexico 1-800-890-2900

www.hussmann.com

© 2017 Hussmann Corporation

Table of Contents

ANSI Z535.5 DEFINITIONS

 ..................iv

INSTALLATION TOOL LIST

 ...............iv

INSTALLATION

UL Listing ..................................................... 1-1
Federal / State Regulations. ............................. 1-1
Location  ....................................................... 1-1
Shipping Damage  ........................................... 1-1
Exterior Loading  ........................................... 1-2
Merchandisers Shipped With End Installed ......... 1-2
Shipping Braces  ............................................. 1-2
Moving Merchandiser Through Narrow 
Store Entrances .............................................. 1-3
Final Location ............................................... 1-5
Leveling ........................................................ 1-5
Door Adjustment ............................................ 1-7
Joining .......................................................... 1-7
Joining Instructions  ....................................... 1-8
Installing Splashguard Brackets  ..................... 1-23
Installing Bumpers ........................................ 1-24

REFRIGERATION / ELECTRICAL

Refrigerant .................................................... 2-1
Refrigerant Piping .......................................... 2-1
Insulation ...................................................... 2-3
Branch Line Piping  ........................................ 2-4
Expansion Valve Adjustment  ........................... 2-5
Refrigeration Thermostat ................................ 2-6
Defrost Termination Thermostat ...................... 2-7
Control Settings Medium Temperature  ............. 2-7
Control Settings Low Temperature ................... 2-7
Merchandiser Electrical Data  ........................... 2-9
Field Wiring  ................................................. 2-9
Electrical Connections  .................................... 2-9
Identification of Wiring  .................................. 2-9
Wiring Color Code  ....................................... 2-10

DRIP PIPING AND SPLASHGUARDS

Waste Outlet and Water Seal ............................ 3-1
Installing Drip Piping ..................................... 3-1
Drip Piping Lineup Arrangements  ................... 3-4
Installing Splashguards  ................................... 3-5
Sealing Splashguard to Floor ........................... 3-6

START UP / OPERATION

Start Up ......................................................... 4-1
Stocking  ........................................................ 4-1
Load Limits .................................................... 4-1
Load Limit Profiles .......................................... 4-2
Installing FDA/NSF Required Thermometer  ...... 4-3

MAINTENANCE

Care and Cleaning ............................................ 5-1
Cleaning Honeycomb Assemblies ........................ 5-2
Cleaning Stainless Steel Surfaces .........................5-3
Cleaning Coils ..................................................5-3
Cleaning Under Merchandisers  ......................... 5-3
Removing Scratches from Bumper ...................... 5-3

SERVICE

Replacing Fan Motors and Blades ...................... 6-1
Replacing Electric Defrost Heaters  .................... 6-3
Replacing Drain Pan Heater  ............................. 6-5
Servicing Vertical Lighting  .............................. 6-6
Servicing Doors and Frames  ............................. 6-6
Replacing Door or Door Frame Parts  ................ 6-6
Replacing Damaged Drain Fitting ..................... 6-6
Repairing Aluminum Coils  ............................... 6-7

WARRANTY

Permit Number:

20-05195

Summary of Contents for RFLNS

































































Reviews:

No comments

Related manuals for RFLNS

Randell 41048A Operator'S Manual preview
41048A
Brand: Randell Pages: 21
Norpe EUROCLASSIC User Manual preview
EUROCLASSIC
Brand: Norpe Pages: 16
Gamko MAXIGLASS MG3 User Manual preview
MAXIGLASS MG3
Brand: Gamko Pages: 68
Mainstreet Equipment 829GMC12B User Manual preview
829GMC12B
Brand: Mainstreet Equipment Pages: 8
Hussmann Impact M1GE Datasheet preview
Impact M1GE
Brand: Hussmann Pages: 4
Hussmann Impact Excel P1X-E Technical Data Sheet preview
Impact Excel P1X-E
Brand: Hussmann Pages: 5
Hussmann IMPACT ED1C-ICE Datasheet preview
IMPACT ED1C-ICE
Brand: Hussmann Pages: 5
Summit SCR1155 Instruction Manual preview
SCR1155
Brand: Summit Pages: 12

Brands by name

Popular brands

Load more brands