2 of 4
ASSEMBLY
Carefully remove the contents from the carton and keep the carton for future storage. Be sure to untangle any wires
that may be tangled with other items. (Please DO NOT forcibly remove any contents.)
Step 1:
Locate the Tree Stand and rotate the legs until the holes on the inner and outer
hub of the stand are aligned, and the stand forms an “X” shape (
see
Fig. A
). Once you
have the holes lined up, insert each of the eye bolts (3 total) into the holes on the
stand’s middle section, being sure that the eye bolts do not extend so far as to interfere
with the installation of the tree pole. Place the stand where you are going to set up the
tree – ensure that it is on a level surface and near a dedicated power source.
THIS
PRODUCT IS SUITABLE FOR INDOOR USE ONLY.
Step 2:
Locate the Tree Bottom Section “A” which is tagged with the letter “A”.
Remove any plastic protective pole caps that are on the bottom of the pole (they can
be saved and reused for storage if desired). Insert Tree Section “A” into the Tree Stand.
Do not force the pole into the Tree Stand. It will slide down to its correct position.
Make sure the pole is firmly seated and standing straight in the Tree Stand. Turn all the
eye bolts until contact is made with the pole. If Tree Section “A” is not sitting straight, then simply loosen the eye bolts,
adjust the tree pole, and retighten the eye bolts. Remove any packing strap that is wrapped around this tree section.
Allow the branches and leaves to fall into place
Step 3:
Locate Tree Top Section “B” which is tagged with the letter “B”. Insert it into the top of Tree Section “A”. Make
sure section “B” is seated securely into the top of section “A”. Remove any packing strap that is wrapped around this
tree section, same as you did for section “A”. Allow the branches and leaves to fall into place
Step 5:
Connect the plug from each tree section into the section below securely. The light sets have colored tags
which state “Please plug in here”, so that you can find the corresponding connections easier. Further secure the
plug connection by screwing the outer cover into place.
Step 6:
In Tree Section “A”, there is a power adapter that is to be guided down through the tree
section to the floor. Insert it into a power outlet in your home or into a U.L. approved extension
cord or power strip (not included). Tap the foot pedal (
see Fig. B
) to turn the lights on. Your tree
should now be lit. If some bulbs do not light, please go to the section on TROUBLESHOOTING FOR
LIGHTS. Press the foot pedal again to turn the tree off.
SHAPING
1.
Plug in the lights as you are shaping the tree.
2.
Remove any packing strap or other packing material that is around the tree section(s) and allow the branches to fall
into place. Some of the branches may catch on one another. If that occurs, slowly press down on each branch until
it falls into its place or gently pull up and out.
Important:
If the branches are connected to the tree’s pole by metal
brackets (hinges), be sure that all wires are free when adjusting the branches.
3.
Shape by section and layer, starting at the bottom of the tree and working your way up to ensure all branches are
shaped.
4.
Due to the height of the tree, it is recommended to shape the top section before placing it on the tree to avoid
shaping from a chair or ladder.
5.
Consult the product photo of the tree during shaping. On each branch, begin with the tips closest to the pole and
work your way to the end of the branch by fanning out the left and right tips from the center tips to resemble a
peacock’s fanned tail. Offset the tip from the tip before to hide the tree’s pole and fill spaces. Continue spreading
the tips until they resemble that of a real tree.
6.
After shaping the whole tree, step back and take an overall look. Shift branches to fill any gaps. Your tree is now
ready to decorate and enjoy!
CLEANING
&
CARE
As you will be using the artificial Christmas tree every year, it is essential to keep it in good condition and clean.
•
Dust gently using a soft cloth or fabric duster.
Fig. B
Fig. A
