2 of 4
Fig. 2
ASSEMBLY
C
AREFULLY REMOVE THE CONTENTS FROM THE CARTON
.
KEEP THE CARTON FOR FUTURE STORAGE
.
DO
NOT
FORCIBLY REMOVE CONTENTS
.
Step 1:
Locate the Tree Stand and rotate the legs until the holes on the inner and outer hub
of the stand are aligned, and the stand forms an “X” shape (
see
Fig. 1
). Once you have the
holes lined up, insert each of the eye bolts (3 total) into the holes on the stand’s middle
section, being sure that the eye bolts do not extend so far as to interfere with the
installation of the tree pole. Place the stand where you are going to set up the tree – ensure
that it is on a level surface and near a dedicated power source.
THIS PRODUCT IS SUITABLE
FOR INDOOR USE ONLY.
IMPORTANT: DO NOT PLACE THE TREE WHERE IT IS LIKELY TO
WOBBLE DUE TO UNEVEN FLOORS OR THICK CARPETING. PLACE THE TREE ON A LEVEL
SURFACE.
Step 2:
Locate the Tree Bottom Section “A” which is tagged with the letter “A”. Remove the green pole cap
(
see Fig. 2
) that is covering the bottom of the pole. It is a protective cover only and can be kept for storage if
desired. Insert Tree Section “A” into the Tree Stand. Do not force the pole into the Tree Stand. It will slide
down to its correct position. Make sure the pole is firmly seated and standing straight in the Tree Stand.
Turn all the eye bolts evenly until contact is made with the pole. If Tree Section “A” is not sitting straight,
then simply loosen the eye bolts, adjust the tree pole, and retighten the eye bolts. Remove any packing
strap that is wrapped around the section. Allow the branches to fall into place. The branches are connected
to the tree pole by metal hinges (
see Fig. 3).
NOTE
:
S
OME BRANCHES MAY CATCH ON ONE ANOTHER
.
IF THAT OCCURS
,
SLOWLY PRESS DOWN ON EACH BRANCH UNTIL IT
FALLS INTO PLACE
.
Step 3:
Locate Tree Middle Section “B” which is tagged with the letter “B”. Insert it into the top of Tree
Section “A”. Make sure section “B” is seated securely. Remove any packing strap that is wrapped around
this tree section. Allow the branches to fall into place.
Step 4:
Locate Tree Middle Section “C” which is tagged with the letter “C”. Insert Tree Section “C” into the top of Tree Section
“B”. Make sure the section is seated securely. Remove any packing strap that is wrapped around this tree section. It is
recommended to shape the Top Section “C” before placing it on the tree. For further information, see section on
SHAPING
.
Step 5:
Locate Tree Top Section “D” which is tagged with the letter “D”. Insert Tree Section “D” into the top of Tree Section
“C”. Make sure the section is seated securely. Remove any packing strap that is wrapped around this tree section. It is
recommended to shape the Top Section “D” before placing it on the tree. For further information, see section on
SHAPING
.
Step 6:
Connect the light set plug(s) from each tree section into the section
below securely. To find the connections easier, the light sets have a
male/female plug with a colored barbell label. For the connection from Section
A to B, there will be a red barbell label with the number one . For the
connection from Section B to C, there will be a yellow barbell label with the
number two . For the connection from Section C to D, there will be a blue
barbell label with the number three . Further secure the plug connection by
screwing the outer cover into place.
Step 7:
In Tree Section “A”, there is a power adapter that is to be guided down through the tree section
to the floor. Insert it into a power outlet in your home or into a U.L. approved power strip (not included).
Tap the foot pedal (
see Fig. 4
) to turn the lights on. Your tree should now be lit. If some bulbs do not light,
please go to the section on TROUBLESHOOTING FOR LIGHTS.
SHAPING
T
HE BRANCHES HAVE BEEN CONDENSED TO FIT INTO THE BOX AND CAN BE EASILY RESHAPED TO THEIR ORIGINAL FULLNESS BY BENDING AND
SEPARATING EACH OF THE BRANCHES IN A MORE REALISTIC MANNER
.
1.
Plug in the lights as you are shaping the tree.
2.
Due to the height of the tree, it is recommended to shape the top section before placing it on the tree to avoid shaping
from a chair or ladder. Reference the image on the cover of this instruction manual to see what the tree should like.
3.
Shape by section and layer, starting at the bottom of the tree and working your way up (or vice versa) to ensure coverage
of the whole tree.
4.
On each branch, begin with the leaves closest to the pole and work your way to the end of the branch.
5.
Fan out the left and right tips from the center tips to resemble a peacock’s fanned tail. Offset the tip from the tip before to
hide the tree’s pole and fill spaces. Continue spreading the tips until they resemble that of a real tree.
6.
After shaping the whole tree, step back and take an overall look. Shift branches to fill any gaps and pull apart any branches
that may be stuck together. Your tree is now ready to decorate and enjoy!
Fig. 1
Fig. 3
!
IMPORTANT:
D
O NOT REMOVE THE
BARBELL LABELS
ON YOUR LIGHT SETS
.
THEY WILL HELP YOU TO EASILY FIND THE
PLUGS AND CONNECT THE FOLLOWING YEAR
.
Fig. 4