2 of 4
ASSEMBLY
C
AREFULLY REMOVE THE CONTENTS FROM THE CARTON
.
KEEP THE CARTON FOR FUTURE STORAGE
.
DO
NOT
FORCIBLY REMOVE
CONTENTS
.
Step 1:
Take the
P
OT
and place it where you are going to set up the tree.
THIS PRODUCT IS SUITABLE FOR INDOOR AND
COVERED OUTDOOR USE.
IMPORTANT: DO NOT PLACE THE TREE WHERE IT IS LIKELY TO WOBBLE DUE TO UNEVEN
FLOORS OR THICK CARPETING. PLACE THE TREE ON A LEVEL SURFACE.
There is a decorative greenery ring sitting inside the P
OT
.
Leave inside the P
OT
and proceed
to Step 2.
Step 2:
Find
T
REE
S
ECTION
A
, tagged with the letter “A”. Remove the green pole cap (
see Fig. 1
) that is
covering the bottom of the pole. It is a protective cover only and can be kept for storage if desired.
Insert T
REE
S
ECTION
A into the P
OT
. Do not force the pole. It will slide down to its correct position.
Make sure the pole is seated firmly in the P
OT
.
Step 3:
Locate
T
REE
S
ECTION
B
, tagged with the letter “B”. Insert T
REE
S
ECTION
B into T
REE
S
ECTION
A.
Make sure the section is sitting securely.
NOTE
:
T
HE TOP
,
INNER PART OF THE POLE TO
T
REE
S
ECTION
B
HAS A
GREEN POLE ADAPTER INSIDE
.
T
HIS POLE ADAPTER IS NOT TO BE REMOVED
.
T
REE
S
ECTION
B
HAS A GREEN STEM COMING OFF THE BOTTOM OF ITS
POLE WHICH FITS SNUGGLY INTO THIS ADAPTER AND GIVES STABILITY TO YOUR TREETOP
.
Step 4:
Connect the light set plug from T
REE
S
ECTION
B into the light set plug in
T
REE
S
ECTION
A. The plugs have a red colored barbell label with the number
one . Further secure the plug connection by screwing the outer cover into
place.
Step 5:
In T
REE
S
ECTION
A, there is a power adapter that is to be guided down
through the tree section to the floor. Insert it into a power outlet in your home or into a U.L. approved power strip (not
included). Your tree should now be lit. If some bulbs do not light, please go to the section on TROUBLESHOOTING FOR
LIGHTS.
SHAPING
T
HE BRANCHES WERE COMPRESSED TO FIT INTO THE BOX AND CAN BE RESHAPED TO THEIR ORIGINAL FULLNESS BY BENDING AND
SEPARATING EACH OF THE BRANCHES IN A MORE REALISTIC MANNER
.
1. Plug in the lights as you are shaping the tree.
2. Please reference the image on the cover of this instruction manual to see what the tree should look like
3. Shape by section and layer, starting at the bottom of the tree and working your way up to ensure coverage of the
whole tree.
4. In T
REE
S
ECTION
A, the branches are hinged to the pole (
see Fig. 2
). Some of the branches may catch
on one another. If that occurs, slowly press down on each branch until it falls into its place or gently
pull up and out. Important: The branches are connected to the tree’s pole by metal brackets
(hinges), be sure that all wires are free when adjusting the branches.
5. On each branch, begin by shaping the tips closest to the pole and work your way to the end of the
branch. Fan the tips up and out to the sides.
6. In T
REE
S
ECTION
B, pull down each branch to an approximate 90° angle to the floor on the lower part and about a 45°
angle on the upper portion. While doing so, offset the branches and tips from one another to fill spaces evenly.
7. After shaping the whole tree, step back and take an overall look. Shift branches to fill any gaps. Your tree is now ready
to decorate and enjoy!
CLEANING
&
CARE
A
S YOU WILL BE USING THE TREE EVERY YEAR
,
THE FOLLOWING ARE TIPS TO KEEP IT IN GOOD CONDITION AND MAINTAINED
:
•
Dust gently using a soft cloth or fabric duster.
•
Do NOT use any chemicals or solvents to clean.
•
Handle the light sets gently. Do NOT pull or tug light sets as this may inadvertently loosen the bulb.
•
Follow all Storage and Safety Instructions.
! IMPORTANT:
D
O NOT REMOVE THE
BARBELL LABELS
ON YOUR LIGHT SETS
.
THEY WILL HELP YOU TO EASILY FIND THE
PLUGS AND CONNECT THE FOLLOWING YEAR
.
Fig. 2
