background image

Trademarks & Copyright 

 

Windows 95/98/ME and Windows NT/2000/XP are registered trademarks of Microsoft Corp. All other brands and 
product names are trademarks of their respective companies. 
 

No part of this publication may be reproduced in any form or by any means or used to make any derivative (such as 
translation, transformation or adaptation) without the express written consent of the manufacturer as stipulated by the 
United States Copyright Act of 1976. 

 

FCC Certifications 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the 
FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential 
installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications.  However, there is no 
guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

Shielded interface cables must be used in order to comply with emission limits. 
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could 
void your authority to operate the equipment. 
This device complies with Part 15 of the FCC rules.  Operation is subject to the following two conditions:  (1) This device 
may not cause harmful interference, and (2) This device must accept any interference received, including interference that 
may cause undesired operation. 
 

CE Mark Warning 

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user 
may be required to take adequate measures. 
All trademarks and brand names are the property of their respective proprietors. 
Specifications are subject to change without prior notification. 

 
 
HAWKING LIMITED WARRANTY 

 

Hawking Technology guarantees that every HPOE1 Power Over Ethernet Adapter Kit is free from physical 
defects in material and workmanship under normal use for (1) year from the date of purchase.  If the product 
proves defective during this one-year warranty period, call Hawking Customer Service in order to obtain a Return 
Authorization number.  Warranty is for repair or replacement only.  Hawking Technology does not issue any 
refunds.  BE SURE TO HAVE YOUR PROOF OF PURCHASE.  RETURN REQUESTS CANNOT BE 
PROCESSED WITHOUT PROOF OF PURCHASE.  When returning a product, mark the Return Authorization 
number clearly on the outside of the package and include your original proof of purchase. 
 
IN NO EVENT SHALL HAWKING TECHNOLOGY’S LIABILTY EXCEED THE PRICE PAID FOR THE 
PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES 
RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE OR ITS 
DOCUMENTATION.  Hawking Technology makes no warranty or representation, expressed, implied or 
statutory, with respect to its products or the contents or use of this documentation and all accompanying software, 
and specifically disclaims its quality, performance, merchantability, or fitness for any particular purpose.  
Hawking Technology reserves the right to revise or update its products, software, or documentation without 
obligation to notify any individual or entity.  Please direct all inquiries to: 

techsupport@hawkingtech.com

.

 

 

Summary of Contents for HPOE1














Reviews: