background image

7

rotation stops when the chain brake is applied.

•   Shut off the engine before setting the chainsaw down.
•   Use extreme caution when cutting small bushes and saplings; 

slender material may catch in the saw chain and be whipped 
towards you or pull you off balance.

•   When cutting a limb that is under tension, be alert for spring 

back so that you will not be struck when the tension in the wood 
fibres are released.

•   Keep the handles dry, clean, and free of oil or fuel mixture.
•   Operate the chainsaw only in well-ventilated areas.
•   DO NOT operate a chainsaw from up in a tree unless you have 

been specifcally trained to do so.

•   All chainsaw servicing, other than the items listed in the 

user manual safety and maintenance instructions, should be 
performed by competent chainsaw service personnel.

•   When transporting your chainsaw, use the appropriate chain bar 

cover.

•   DO NOT operate your chainsaw near or around flammable 

liquids or gases, whether inside or outdoors. An explosion and/
or fire may result.

•   DO NOT fill the fuel tank, oil reservoir or lubricate whilst the 

engine of the chainsaw is running.

•   USE THE CORRECT TOOL: Cut wood ONLY. Do not use 

the chainsaw for purposes for which it was not intended. For 
example, do not use the chainsaw for cutting plastic, masonry 
or building materials.

•   The engine will create toxic exhaust fumes as soon as the 

engine is started. Never work in enclosed areas or in areas with 
poor ventilation.

•   NOTE: The chainsaw is designed for noncommercial, occasional 

use and for general work, such as stump grubbing, and cutting 
firewood, etc.

Summary of Contents for 75716






























Reviews: