2 5 6 4 B A L E B U S T E R
O P E R A T I N G I N S T R U C T I O N S
27
3.3.13 Loading the bale
The bale conveyor must not be running when a bale is lifted into the shredding chamber. (
step3-5),
dropping bales on
to the moving conveyor slats may bend slats.
DANGER:
If it is necessary to transport a second bale over uneven terrain, make sure any
bystanders are away from the 2564 BALEBUSTER. Serious injury or death could result if the bale
rolls off the loader main frame loader supports.
STEP 1:
Lower the bale loader part way down so you can so you can still see the end of the tine fork.
Use the fork as a guide and back up to the first bale, with the bale loader in its lowest position, back up
until the bale is loaded on the main frame loader supports
STEP 2:
Slowly lift bale, until the flat end is frimly against the table. If you need to travel to the second
bale, transport with the bale loader on the main frame supports, use the bale as a guide to line up the
second bale.
STEP 3-5:
Slowly lift bale into the shredding chamber. Continue lifting the bale loader until it stops. The
correct position for shedding a single bale will help prevent spillage.
NOTE:
If bale does not rotate forward the twine may be over the tine. Cut the twine at this time to
prevent damage to the machine.
STEP 6:
Load a second bale (if the first bale is on the main frame loader supports, use the bale as a
guide to line up on the second bale). (If the first bale is in the shredding chamber use the conveyor and
move the bale to the right so you can look past it on the left side). Back trailer until bale is loaded on the
main frame loader supports. Slowly lift the bale off the ground keeping the weight of the bale on the main
frame loader supports. This is the transport position for the second bale.
STEP 7:
After the first bale is shredded, repeat steps, 3-5, loading and shredding the bale.
figure 3.6
loading the bale
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
Summary of Contents for Balebuster 2564
