background image

 

 

 

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 

Page 12 of 24 

Max-Flo VS Pump

 

IS2300VSP   Rev C 

 

 

WARNING

 – Return to filter to close filter manual air relief valve when a steady stream of water (not air or air 

and water) is discharged from valve.  Failure to do so could result in severe personal injury. 

 

ATTENTION

 

– NEVER OPERATE THE PUMP WITHOUT WATER

.  Water acts as a coolant and lubricant for the 

mechanical shaft seal.  NEVER run pump dry.  Running pump dry may damage seals, causing leakage, flooding, and 
voids warranty.  Fill strainer housing with water before starting motor. 

 

ATTENTION

 – Do NOT add chemicals to pool/spa system directly in front of pump suction.  Adding 

undiluted chemicals may damage pump and voids warranty. 

 

ATTENTION

 – Before removing strainer cover: 

1.

 

STOP PUMP before proceeding. 

2.

 

CLOSE VALVES in suction and outlet pipes. 

3.

 

RELEASE ALL PRESSURE from pump and piping system using filter manual air relief valve.  See filter owner’s 
manual for more details. 

4.

 

Remove strainer cover and fill strainer housing with water. 

5.

 

Clean and lubricate strainer cover O-ring with "Jack's 327" if necessary. 

6.

 

Replace strainer cover on strainer housing.                                                                                                                          

NOTE - Tighten strainer cover lock ring by hand only (no wrenches).

 

7.

 

OPEN VALVES in suction and outlet pipes. 

Turn on power and wait for pump to prime, which can take up to ten (10) minutes.  Priming time will depend on 
vertical length of suction lift and horizontal length of suction pipe. If pump does NOT prime within 10 minutes, stop 
motor and determine cause.  Be sure all suction and discharge valves are open when pump is running.  See 
Troubleshooting Guide. 

6.3.

 

User Interface Summary 

Figure 6.3-1 

 

Summary of Contents for Max-Flo VS SP2300VSP

























Reviews: