5
Programming Menu Flowchart
The OnCommand’s five menus have many items that allow you to customize the operation of your pool/spa
equipment. The chart below shows the OnCommand’s menus as well as each menu’s specific settings.
22
Remote Menus
Enabled
Toggle between Enabled (default) and Disabled Remote Menus
Move to previous/next configuration menu
This feature will prevent unauthorized access to the Settings, Timers, and Configuration menus from
any of the OnCommand’s remote display/keypads. When disabled, the remote display/keypads will
only show the default menu and allow on/off control via the pushbuttons. Note that the function of
the OnCommand’s built-in display/keypad is unchanged by this selection. Once disabled, the only
way to enable “Remote Menus” is to use the local display/keypad.
All Timeclocks
7-day
Move to previous/next configuration menu
Toggle between 7-day (default) and Weekend/Weekday time options
This selection affects ALL of the timeclock logic in the OnCommand. If “7-day” is selected, each
timeclock will have one set of turn-on/turn-off settings that operate every day of the week. If “Weekend/
Weekdays” option is selected then the user can enter one set of turn-on/turn-off times for the weekend
(fixed as Saturday/Sunday) and another set of turn-on/turn-off times for weekdays (Monday through
Friday).
Time Format
12 hour AM/PM
Units
ºF and PPM
Move to previous/next configuration menu
Move to previous/next configuration menu
Toggle between 12 hour AM/PM (default) and 24 hour time format options
Toggle between ºF and PPM (default) and ºC and g/L (Metric) options
Reset Config. to
Default Press +
Are you sure?
+ to proceed
Config. reset
Confirmed
Initiate reset of all configuration parameters
Reset all configuration parameters
Move to previous/next configuration menu (config. not reset)
Move to previous/next menu (config. not reset)
Move to previous/next configuration menu
Use this function to erase all previous system configuration and reset all configuration parameters
back to the factory default values. This function is NOT reversible--be careful.
Quick “How To” Guide
Operate the Spa—Manually
1. Press the “Pool/Spa” button to go to “spa-only” operation (right LED illuminated). In some cases,
this may take more than one press of the button.
2. If the filter pump is not already on, press the “FILTER” button to turn it on.
3. If the spa is below the desired temperature, the heater will turn on automatically when the filter pump
is on and the valves are in the spa-only position. If you have not already set the desired temperature
for the spa, see “Set Heater Temperature” below.
4. If the spa has a separate jet pump and or blower, determine if the jet pump/blower is controlled by
Aux1 or Aux2 (it should be marked on the label inside the door). Then press the appropriate button
to turn on the jets/blower.
Operate the Spa—Automatically
1. Press the “MENU” button repeatedly until “Timers Menu” is displayed.
2. Press the “>” button repeatedly until the “Spa—all” or “Spa—wkend” is displayed.
3. Use the “+” and “-“ buttons to set the desired start time, then press “>” to switch to the off time. Use
the “+” and “-“ buttons to adjust the off time. If you are setting the “weekend” timeclock, press “>” to
go to the “weekday” settings.
denotes conditional items
12 hour or 24 hour time format
ºF or ºC
reset to default
default menu
day and time
water temperature
air temperature
chlorinator setting
salt level
reason pump is running (not scheduled)
reason hi-speed is running (not scheduled)
countdown time remaining
heater control status
system manual off
check system error
filter speed
settings menu
spa heater temperature
pool heater temperature
spa solar temperature
pool solar temperature
superchlorinate
spa chlorinator setting
pool chlorinator setting
spa high/low speed
pool high/low speed
day and time
backlit display light
beeper
teach wireless remote
wireless channel
timers menu
pool filter pump
spa
lights
aux1
aux2
valve3
superchlorinate
diagnostic menu
salt level
water sensor
air sensor
solar sensor
main software revision
display software revision
filter bridge/vsc software revision
RF base software revision
configuration menu
chlorinator
pool/spa
filter
heater
solar
lights
aux1
aux2
valve3
remote menus
7-day or weekend/weekday timeclock
