1. When adjusting the signal level on the receiver unit,
MAX and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate
signal level setting may cause overpowering issue that would shorten the product life significantly!
2. Wrongly insert IR blaster and IR receiver to wrong 3.5mm infrared sockets may result in the failure of
the IR extenders. Please check carefully before plugging in the IR extender to the respective IR
sockets.
3. If the DVI or HDMI device requires the EDID in
and provide DVI or HDMI display EDID information.
4. All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz UTP
cable and ASTRODESIGN Video Signal Generator VG
5. The transmission length is largely affected by the type of Cat
and the type of HDMI display. The testing result shows solid UTP cables (usually in the form of 300m
[1,000ft] bulk cables) can transmit a lot l
fixed length patch cords). Shielded STP cables are better suited than unshielded UTP cables. A solid
UTP Cat-5e cable shows longer transmission range than stranded STP Cat
extension applications, solid UTP/STP cables are the only viable choice.
6. EIA/TIA-568-B termination (T568B) for Cat
7. To reduce the interference among the unshielded twisted pairs of wires in Cat
use shielded STP cables to improve EMI problems, which is worsen in long transmission.
8. Because the quality of the CAT5/6 cables has the major effect on how long the transmission limit can
achieve and how good is the received picture quali
choice of Cat-5/5e/6 cables. For desired resolutions greater than 1080i or 1280x1024, a Cat
recommended.
9. If your HDMI display has multiple HDMI inputs, it is found that the first HDMI inpu
generally can produce better transmission performance among all HDMI inputs.
Performance Guide for HDMI over Category Cable Transmission
Performance rating
Wiring
Shielding
Solid
Unshielded (UTP)
Shielded (STP)
Stranded
Unshielded (UTP)
Shielded (STP)
Termination
NOTICE
When adjusting the signal level on the receiver unit, please dial the rotary control switch from MIN to
MAX and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate
signal level setting may cause overpowering issue that would shorten the product life significantly!
ongly insert IR blaster and IR receiver to wrong 3.5mm infrared sockets may result in the failure of
the IR extenders. Please check carefully before plugging in the IR extender to the respective IR
If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to retrieve
and provide DVI or HDMI display EDID information.
All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz UTP
cable and ASTRODESIGN Video Signal Generator VG-859C & VG-870B.
The transmission length is largely affected by the type of Cat-5/5e/6 cables, the type of HDMI sources,
and the type of HDMI display. The testing result shows solid UTP cables (usually in the form of 300m
[1,000ft] bulk cables) can transmit a lot longer signals than stranded UTP cables (usually in the form of
fixed length patch cords). Shielded STP cables are better suited than unshielded UTP cables. A solid
5e cable shows longer transmission range than stranded STP Cat
ension applications, solid UTP/STP cables are the only viable choice.
B termination (T568B) for Cat-5/5e/6 cables is recommended for better performance.
To reduce the interference among the unshielded twisted pairs of wires in Cat-5/5e/6
use shielded STP cables to improve EMI problems, which is worsen in long transmission.
Because the quality of the CAT5/6 cables has the major effect on how long the transmission limit can
achieve and how good is the received picture quality, the actual transmission range is subject to one's
5/5e/6 cables. For desired resolutions greater than 1080i or 1280x1024, a Cat
If your HDMI display has multiple HDMI inputs, it is found that the first HDMI inpu
generally can produce better transmission performance among all HDMI inputs.
Performance Guide for HDMI over Category Cable Transmission
Type of category cable
CAT5
CAT5e
Please use
EIA/TIA-568-B
termination (
T568B
please dial the rotary control switch from MIN to
MAX and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate
signal level setting may cause overpowering issue that would shorten the product life significantly!
ongly insert IR blaster and IR receiver to wrong 3.5mm infrared sockets may result in the failure of
the IR extenders. Please check carefully before plugging in the IR extender to the respective IR
formation, please use EDID Reader/Writer to retrieve
All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz UTP
5/5e/6 cables, the type of HDMI sources,
and the type of HDMI display. The testing result shows solid UTP cables (usually in the form of 300m
onger signals than stranded UTP cables (usually in the form of
fixed length patch cords). Shielded STP cables are better suited than unshielded UTP cables. A solid
5e cable shows longer transmission range than stranded STP Cat-6 cable. For long
5/5e/6 cables is recommended for better performance.
5/5e/6 cable, one can
use shielded STP cables to improve EMI problems, which is worsen in long transmission.
Because the quality of the CAT5/6 cables has the major effect on how long the transmission limit can
ty, the actual transmission range is subject to one's
5/5e/6 cables. For desired resolutions greater than 1080i or 1280x1024, a Cat-6 cable is
If your HDMI display has multiple HDMI inputs, it is found that the first HDMI input [HDMI input #1]
Performance Guide for HDMI over Category Cable Transmission
CAT6
T568B
) at any time
