background image

4

Hearth & Home Technologies  •  LOGS-60 Installation Instructions  •  2321-948 Rev. D  •  10/15

Please contact your Hearth & Home Technologies dealer with 

any questions or concerns. 

For the location of your nearest Hearth & Home Technologies 

dealer, 

please visit www.hearthnhome.com.

Hearth & Home Technologies 

7571 215th Street West, Lakeville, MN 55044

www.hearthnhome.com

WARNING

Delayed Ignition Risk

•  Place media according to instructions.
•  Do NOT place media in area in front of pilot.
•  Do NOT place media in a position that they 

may fall into area in front of pilot.

•  Do NOT use any media other than the media supplied 

with the appliance.

•  Do NOT use more than the amount shipped with the 

appliance.

Fireplace will not function properly. 
Delayed ignition may occur.

18. Place media on media tray according to instructions in-

cluded with media kit.  Once the logs are installed, there 
will not be room for all of the media originally installed.  
The amount used should decrease by approximately 

fi

 ve pounds (1 bag). 

19.  Replace 

fi

 xed glass assembly and decorative front on 

appliance.

NOTICE: 

Do not reinstall all glass media.  Decrease amount 

used by 

fi

 ve pounds (1 bag).

Figure 13.  Log Set Installed

18. 

LOG #7 (SRV2300-708):

 Install Log # 7. Place log so 

that the forked end is facing the 

fi

 rebox opening and the 

left limb is in contact with the locating screw. The other 
end of the log will rest on the Log #1 already placed on 
the right side and should be as far forward as possible 
without interfering with glass installation.

Figure 12.  Log #7 (SRV2300-708)

7

7

55

11

Summary of Contents for MEZZO1600

Page 1: ...D FIXTURE INSTALLATION 1 Remove decorative front 2 Remove fixed glass assembly by unlatching the four top spring latches Allow the fixed glass assembly to tilt away from the fireplace and lift the fixed glass assembly up and out of the opening 3 Lift burner rails out of appliance 4 Remove any existing media from appliance 5 Install eleven shoulder screws into pilot holes in media tray Locations ar...

Page 2: ...g 9 have holes located on the bottom that are used for placement on corresponding shoulder screws See Figure 5 Figure 5 Log Placement Holes Figure 3 Insert Screws into Burner Ports 10 Remove burner port fixture Discard Reinstall burner rails 9 Insert six self tapping screws into the 6 burner ports that lie within the burner port fixture rectangle holes See Figure 3 Move the burner port fixture to ...

Page 3: ...r position Figure 7 Log 2 SRV2300 704 1 1 2 2 3 3 1 1 2 2 Figure 8 Log 3 SRV2331 708 15 LOG 4 SRV2331 706 Install Log 4 onto shoulder screw 6 by lining up shoulder screw with hole in bot tom of log The other end of the log should rest on the end of Log 3 See Figure 9 Figure 10 Log 5 SRV2331 704 Figure 6 Log 1 SRV2300 703 Left and Right Side Placement 1 1 1 1 Figure 9 Log 4 SRV2331 706 4 4 3 3 2 2 ...

Page 4: ...th the appliance Fireplace will not function properly Delayed ignition may occur 18 Place media on media tray according to instructions in cluded with media kit Once the logs are installed there will not be room for all of the media originally installed The amount used should decrease by approximately five pounds 1 bag 19 Replace fixed glass assembly and decorative front on appliance NOTICE Do not...

Reviews: