11
CONSOLE DESCRIPTION
Refer to the drawing on page 10. Note: If there is a
thin sheet of clear plastic on the face of the con-
sole, remove it.
A. Exercise feedback display—This display features
seven modes that give you instant exercise feed-
back: your current speed, the elapsed time (or the
time remaining in a Smart program), the distance
that you have pedaled, the resistance level, the
approximate numbers of calories and fat calories
you have burned (see FAT BURNING on page 20),
and your heart rate (when you use the handgrip
pulse sensor or the optional chest pulse sensor). If
the scan mode is selected, the display will change
from one mode to the next every six seconds. Or,
you can select a single mode for continuous display.
Note: The console can show speed and distance
in either miles or kilometers. To change the unit
of measurement, hold down the On/Reset button
for six seconds. The mode indicators (see F
below) will show which unit of measurement is
selected. When the batteries are replaced, it may
be necessary to reselect the desired unit of
measurement.
B. Increase and decrease arrows—During Smart pro-
grams and iFIT.com programs, these arrows will
prompt you to increase or decrease your pace to
match the target pace.
C. Manual mode/program indicators—When a Smart
program is selected, the upper right corner of the
display will show a 1, 2, 3, 4, 5, 6, 7, or 8, depend-
ing on which Smart program is selected. When the
iFIT.com mode is selected, the upper right corner
will show the letters IF. When the manual mode is
selected, the upper right corner will be blank.
D. Program profiles—These profiles show how the
resistance of the exercise cycle and the target pace
will change during Smart programs. For example,
profile number 6 shows that during Smart program
6, the resistance will gradually increase during the
first half of the program, and then gradually
decrease during the last half; the target pace will
alternately increase and decrease throughout the
program.
E. Warning—see page 3.
F. Feedback mode indicators—These indicators show
which feedback mode (scan, speed, time, distance,
resistance level, calories, fat calories, or heart rate)
is currently shown. Note: When the distance is
shown, the word Miles or the letters Kms will
appear; when your speed is shown, the letters MPH
or Km/H will appear.
G. Pace bar graphs—When the manual mode is
selected, only the left bar graph will appear. This
bar graph represents your exercise pace. As you
increase or decrease your pace, additional bars will
appear or disappear in the bar graph. When a Smart
program or the iFIT.com mode is selected, both bar
graphs will appear. The left bar graph will represent
your exercise pace, and the right bar graph will rep-
resent a target pace. During the program, the target
pace will periodically change. As the right bar graph
changes, simply adjust your pace so that the same
number of bars appear in both bar graphs.
Important: The target pace is a
goal
pace. Your
actual pace may be slower than the target pace,
especially during the first few months of your
exercise program. Make sure to exercise at a
pace that is comfortable for you.
H. On/Reset button—When the console is off, pressing
this button will turn on the display. When the console
is on, pressing this button will reset the display.
This button is also used to select the unit of meas-
urement for speed and distance (see A at the left).
I. Display Mode button—This button is used to select
the feedback modes. The modes will be selected in
the following order: scan, speed, time, distance,
resistance level, calories, fat calories, and heart
rate (when the handgrip pulse sensor or the option-
al chest pulse sensor is used).
J. + and – buttons—These buttons control the resist-
ance of the exercise cycle. There are ten resistance
levels; level 10 is the most challenging.
K. Program button—This button is used to select the
manual mode and Smart programs.
L. IFIT.com button—This button is used to select the
iFIT.com mode. The indicator above the button will
light when the iFIT.com mode is selected.
To use the manual mode of the console,
refer to
page 12.
To use a Smart program,
refer to page 13.
To use iFIT.com CDs or videos,
refer to page 17.
To
use a program directly from our Web site,
refer to
page 18.
