background image

Part No. 326128 R0412A 

Printed in China © 2012 ICON IP, Inc.

ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and 
material, under normal use and service conditions. The frame is warranted for a lifetime. Parts and labor 
are warranted for one (1) year from the date of purchase. 

This warranty extends only to the original purchaser (customer). ICON’’s obligation under this warranty is 
limited to repairing or replacing, at ICON’’s option, the product through one of its authorized service centers. 
All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped 
to a service center, freight charges to and from the service center will be the customer’’s responsibility. If 
replacement parts are shipped while the product is under warranty, the customer will be responsible for a 
minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge. 
This warranty does not extend to freight damage to the product. This warranty will automatically be voided 
if the product is used as a store display model, if the product is purchased or transported outside the USA, 
if all instructions in this manual are not followed, if the product is abused or improperly or abnormally used, 
or if the product is used for commercial or rental purposes. No other warranty beyond that speci

 cally set 

forth above is authorized by ICON.

ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in con-
nection with the use or performance of the product; damages with respect to any economic loss, loss of 
property, loss of revenues or pro

 ts, loss of enjoyment or use, or costs of removal or installation; or other 

consequential damages of any kind. Some states do not allow the exclusion or limitation of incidental or 
consequential damages. Accordingly, the above limitation may not apply to the customer.

The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of 
merchantability or 

 tness for a particular purpose are limited in their scope and duration to the terms set 

forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the 
above limitation may not apply to the customer.

This warranty provides speci

 c legal rights; the customer may have other rights that vary from state to state.

ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813

LIMITED WARRANTY

IMPORTANT: You must register this product within 30 days of the purchase date to avoid added 
fees for service needed under warranty. Go to www.healthriderservice.com/registration.

To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to 
provide the following information when contacting us:

••  the model number and serial number of the product (see the front cover of this manual)

••  the name of the product (see the front cover of this manual)

••   the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED 

DRAWING near the end of this manual)

ORDERING REPLACEMENT PARTS

Summary of Contents for H95e Elliptical





























Reviews: