5
12
1. Make sure that there are 3” Endcaps (27) on the ends
of both Stabilisers (30).
Hold one of the Stabilisers (30) against the saddle on
the front of the Base (1). Attach the Stabiliser with two
3/8” x 3 1/2” Carriage Bolts (28) and two 3/8” Nylon
Locknuts (29).
2. Hold the other Stabiliser (30) against the saddle on the
rear of the Base (1). Attach the Stabiliser with two 3/8”
x 3 1/2” Carriage Bolts (28) and two 3/8” Nylon
Locknuts (29).
The following guidelines will help you to plan your
exercise program. Remember that a proper diet and
adequate rest are essential for successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. For effective exercise, your heart
rate should be maintained at a level between 70% and
85% of your maximum heart rate as you exercise. This
is known as your training zone.
You can find your training zone in the table below.
Training zones are listed according to age and physi-
cal condition.
Burning Fat
To burn fat, you must exercise at a low intensity level
for a sustained period of time. During the first few
minutes of exercise, your body uses easily accessible
carbohydrate calories for energy. Only after the first few
minutes of exercise does your body begin to use stored
fat calories for energy. If your goal is to burn fat, adjust
the intensity of your exercise until your heart rate is
near the low end of your training zone as you exercise.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the intensity of your exercise until your heart
rate is near the middle of your training zone.
HOW TO MEASURE YOUR HEART RATE
To measure your
heart rate, stop
exercising and
place two fingers
on your wrist as
shown. Take a
six-second
heartbeat count,
and multiply the
result by ten to
find your heart
rate. (A six-sec-
ond count is used because your heart rate drops
quickly when you stop exercising.) If your heart rate is
too high, decrease the intensity of your exercise. If
your heart rate is too low, increase the intensity of
your exercise.
WORKOUT GUIDELINES
Each workout should include three important parts:
(1) a warm-up, (2) training zone exercise, and (3) a
cool-down.
Warming up
Warming up prepares the body for exercise by
increasing circulation, delivering more oxygen to the
muscles, and raising the body temperature. Begin
each workout with 5 to 10 minutes of stretching and
light exercise to warm up.
20
138-167
133-162
25
136-166
132-160
30
135-164
130-158
35
134-162
129-156
40
132-161
127-155
45
131-159
125-153
50
129-156
124-150
55
127-155
122-149
60
126-153
121-147
65
125-151
119-145
70
123-150
118-144
75
122-147
117-142
80
120-146
115-140
85
118-144
114-139
AGE
UNCONDITIONED
TRAINING ZONE
(BEATS/MIN)
CONDITIONED
TRAINING ZONE
(BEATS/MIN)
CONDITIONING GUIDELINES
WARNING: Before beginning this or any exer-
cise program, consult your physician. This is
especially important for persons over the age
of 35 or persons with pre-existing health
problems.
3. Refer to the inset drawing. Feed the console wire har-
ness into the Upright (3), until the end of the console
wire harness extends from the bottom of the Upright.
Whilst another person holds the Upright (3), connect
the console wire harness to the Main Wire Harness
(39). If the wire harnesses do not fit together easily,
turn them—do not force them together. After you
have connected the wire harnesses, pull any slack
in the wire harnesses up through the Upright.
Slide the Upright (3) onto the welded bolts on the Base
(1). Be careful to avoid pinching the wire harnesses.
Tighten a 3/8” Nylon Locknut (29) onto each welded bolt.
1
27
1
30
29
28
27
2
1
30
29
28
3
Console
Wire
Harness
29
29
3
1
39
3
Console
Wire
Harness
4. Attach the Handlebar (9) and the Console Back (86)
to the bracket on the Upright (3) with two 1/4” x 1/2”
Screws (71) and two 1/4” Nylon Half Nuts (78).
78
9
86
3
71
4
