TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department.
PROBLEM: The power does not turn on
SOLUTION:
a. Make sure that the power cord is plugged into a properly earthed outlet (see page 9). If an extension
cord is needed, use only a 3-conductor, 1 mm
2
(14-gauge) cord that is no longer than 1.5 m (5 ft.).
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
PROBLEM: The power turns off during use
SOLUTION:
a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call our Customer Service Department.
PROBLEM: The displays of the console do not function properly
SOLUTION:
a.
UNPLUG THE POWER CORD.
Check the batteries in the console. If the batteries need to be re-
placed, see assembly step 8 on page 8. Most problems are the result of drained batteries.
b. Remove the key from the console and
UNPLUG THE POWER CORD.
Remove the screws from
the hood. Carefully remove the hood.
Locate the Reed Switch (44) and the Magnet (45) on
the left side of the Pulley (50). Turn the Pulley until the
Magnet is aligned with the Reed Switch.
Make sure
that the gap between the Magnet and the Reed
Switch is about 3 mm (1/8 in.).
If necessary, loosen
the Screw (33) and move the Reed Switch slightly.
Retighten the Screw. Re-attach the hood, and run the
treadmill for a few minutes to check for a correct
speed reading.
PROBLEM: The walking belt slows when walked on
SOLUTION:
a. If an extension cord is needed, use only a 3-conductor, 1mm
2
(14-gauge) cord that is no longer
than 1.5 m (5 ft.).
Tripped
Reset
c
45
44
33
Top
View
3 mm
50
b
6
15
1. With the help of a second person, carefully raise the
Uprights (11) until the treadmill is in the position shown.
Insert one of the Extension Legs (34) into the treadmill
as shown. (Note: It may be helpful to tip the Uprights [11]
in the direction shown by the arrow as you insert the
Extension Leg.) Make sure that the Base Pad (40) is un-
derneath the Extension Leg. Attach the Extension Leg
with an Extension Leg Screw (108);
push on the head
of the Extension Leg Screw whilst tightening it.
Attach the other Extension Leg (34) in the same way.
Extension Leg Screw (108)–2
Long Screw (3)–6
Handrail Screw (53)–2
11
1
ASSEMBLY
Assembly requires two people.
Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Assembly requires the included allen wrench
and your own phillips screwdriver and wire cutters .
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
34
108
11
40
WARNING:
Do not plug in the power
cord until the treadmill is completely assembled.
2. Insert a Handrail (1) into the tube at the upper end of the
right Upright (11). Have a second person hold the
Handrail whilst you complete step 3.
11
1
2
