Step 1:Insert battery to the transmitter
to be used (bell push).
Step 2:Insert batteries to the receiver
to be used (chime unit).
S t e p 3 : E n t e r p a i r i n g m o d e f o r
receiver (chime unit).
Press and hold the zone
Select button for 3 seconds.
The LED #1 will flash.
Step 4: Press the button again to
move to the zone you wish to pair with. Press melody
selector to scroll through the melodies. Once you hear
your preferred melody, do not press again as it is now
selected.
Step 5: Once the zone and melody are selected, press the bell
push button once to pair. If successful, the receiver
(chime) will generate a short tone. Press the button to
exit pairing mode, the system is ready to use.
USER MANUAL
TM
EchoChime300
WIRELESS Home Alert System
1
WARNING
The user is cautioned that changes and modifications made to
the equipment without the approval of Hearing Products
International Ltd could void the user's authority to operate this
equipment.
The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment.
MAINTENANCE
- For best results, use good quality alkaline batteries.
- Always replace old or weak batteries.
- Keep doorbell dry. If wet, dry immediately.
- Do not use cleaning solvents on electronic products.
- Solvents contain chemicals that can damage circuitry.
Use damp towel or cloth to clean. Dry immediately.
- Do not expose the bell unit to rain or immerse in water.
It is not water resistant.
If the device is operated using a mains adapter, only use
the Hearing Products International Ltd approved mains adapter.
Do not use any other type of mains adapter.
2
PARTS & FUNCTION DOOR BELL
Battery compartment
Battery cover
Speaker
ID
Flasher
Zone select button
Melody
selector button
Reset
DC jack
Hanging Hole
Volume control
Receiver
Doorbell pusher
Function Switch
Call button
Name plate
Battery
compartment
MOUNTING
Or
Hang on the wall
Stand on the desk
or use sticker provided
Receiver
Door bell pusher
POWER
Doorbell pusher
Receiver
-
+
12V DC
400mA
Using C size Battery
'C
' S
iz
e
1
.5
V
'C
' S
iz
e
1
.5
V
'C
' S
iz
e
1
.5
V
or
+
CR2032
Open the cover
3
First, press and hold the button for 3 seconds to enter the pairing
mode. Press the button to move to the zone which is to be
deleted. Press and hold the and buttons together for 3
seconds.
The receiver will generate a tone to indicate the transmitter on this
zone has been deleted.
First, press and hold the button for 3 seconds to enter the pairing
mode. Press the button to move to the zone then press the
button to select the melody required. Press the button until the
pairing mode is exited.
CODE PAIRING & MELODY SELECTION
ID
Zone select button
Melody selector button
C
H
IM
E
L
IG
H
T
L
IG
H
T & C
H
IM
E
Clear the transmitter on the Chime memory
Change the melody in desired zone
Battery low indicator
If a zone LED light is blinking, it indicates that the battery is low for
this transmitter. You must replace the battery as soon as possible.
If the white flash at the top of the Chime blinks every 5 seconds,
this indicates the receiver batteries are low. You must replace the
batteries of the receiver.
4
5
PLEASE NOTE THE BELL PUSH AND CHIME ARE PAIRED
AND READY TO USE.
To stop the Chime whilst it is alerting press the reset button
PARTS & FUNCTION DOOR BELL
MOUNTING
Or
Hang on the wall
Clip on the Belt
POWER
Using 2 x AA size Battery
Reset
Speaker
ID
Reset
Melody
button
Zone select
button
Belt Clip
Function switch
Vibration &
Melody
Melody
Vibration
OPEN
OPEN
Battery Compartment
Reset
Reset
1. Slide to open the battery
cover
2. Insert 2 AA batteries
3. Close the battery cover.
First, press and hold the button for 3 seconds to enter the pairing
mode. Press the button to move to the zone which is to be
deleted. Press and hold the and buttons together for 3
seconds.
The receiver will generate a tone to indicate the transmitter on this
zone has been deleted.
First, press and hold the button for 3 seconds to enter the pairing
mode. Press the button to move to the zone then press the
button to select the melody required. Press the button until the
pairing mode is exited.
Step 1: Insert battery to the transmitter to be used (bell push).
Step 2: Insert batteries to the pager
Step 3: Enter pairing mode for
receiver (pager unit).
Press and hold the zone select
button for 3 seconds.
The LED #1 will flash.
Step 4: Press the button again to move to
the zone you wish to pair with.
Press melody selector to scroll
through the melodies. Once you hear
your preferred melody, do not press
again as it is now selected.
Step 5: Once the zone and melody are selected with the zone icon
flashing, trigger the transmitter once to pair. If successful,
the receiver (pager) will generate a short tone. Press the
button to exit pairing mode, the system is ready to use.
CODE PAIRING & MELODY SELECTION
Clear the transmitter on the Chime memory
Change the melody in desired zone
Battery low indicator
If a zone LED light is blinking, it indicates that the battery is low for
this transmitter. You must replace the battery as soon as possible.
If the receiver beeps every 5 seconds, this indicates the receiver
batteries are low. You must replace the batteries of the receiver.
6
7
PLEASE NOTE THE BELL PUSH AND CHIME ARE PAIRED
AND READY TO USE.
To stop the Chime whilst it is alerting press the reset button
VIBRATING PAGER
ON/off button
ON/OFF button
Microphone
Sensitivity
Power On/OFF
Battery
compartment
Battery Installation
+
+
Insert 2 AAA battery compartment
Turn ON and turn OFF
This device has two ways to turn power on and off.
Hardware ON/OFF
Slide the switch to ON or OFF
position.
If the slide switch is OFF, you cannot use the
software switch to turn on the power. If the unit is
not in use for a long period, use the hardware
switch to turn off the unit
Software ON/OFF
This allows the transmitter to
be controlled externally.
Off: If the sensor is ON, press and hold the
software ON/OFF switch 5 seconds, the LED will
flash.
ON: If the sensor is OFF, press and hold the
software ON/OFF switch 5 seconds, the LED will
flash.
The sound sensor defaults to "ON" when the
hardware switch is moved from OFF to ON.
Hardware switch
Software switch
8
Code Matching & Melody Selection
The sound sensor works with the receiver (chime) and must be
paired prior to use.
Step 1: Insert batteries in the sensor to be used.
Step 2: Insert batteries in the receiver to
be used.
Step 3: Enter pairing mode for receiver
(chime unit). Press and hold the
zone selector button 3 seconds.
The LED #1 will flash.
Step 4: Press the button again to move
to the zone you want to pair with.
Press melody selector to
scroll through the melodies. Once
you hear you preferred melody, do
not press again as it is now s e l e c t e d .
Step 5: Switch on the sensor and speak into t h e m i c r o p h o n e ,
the red LED indicator will light. If s u c c e s s f u l , t h e
receiver will generate a short tone.
Press the
button to exit pairing mode, the system is
ready to use
ID
Zone selector
button
Melody
selector
C
H
IM
E
L
IG
H
T
L
IG
H
T & C
H
IM
E
Operation
1. Open the cover.
2. Slide the power to the ON position,
3. Select the desired sensitivity low, mid, or high, this sets the level
of sound required to trigger the transmitter.
4. Stick the microphone to the device you want to detect.
Open the cover
Slide the on/off switch
to OFF position
While pressing the test button
Slide the on/off switch to 'on'
position and hold the button 5
seconds. The LED will flash 5 times
when a new code is generated
Code Conflict
If the sound sensor coding and another transmitter is the same.
you must change the code of the sound sen
sor.
When you have changed the code of the sound sensor you will then
need to re- pair the sound sensor with the receiver.
9
Vibration Pad
On/Off
Vibration out
Indicator
Part & Function
Setup
DC jack
Bed Shaker
On/Off
Vibration out
BED SHAKER
Vibrator
Wire
plug
This Bed Shaker must be worked with the Echochime 300 when using the
vibration function.
On
Off
Pad
Pad
On
12V
Ready
12V ready indicator
Pad On inducator
Using 12V 400mA AC/DC
adaptor.
DC jack:
If using the Bed Shaker , it must be connected with a 12V 400mA AC/DC
adaptor to this jack.
12V ready indicator:
This indicator will light up, when the 12V adaptor is
connected correctly.
Bed Shaker on/off:
Slide this switch to turn on or turn off the vibration
function.
Pad on indicator:
If the Bed Shaker on/off switch is slide to on position, this LED
indicator will light up to indicate vibration function is ready.
Vibration out:
Plug the Bed Shaker to this jack.
12V DC
400mA
Using the Bed Shaker, it must
be connected with a 12V
400mA AC/DC adaptor
06-2016
