background image

15

Hearth & Home Technologies  •  B41L-AU Owner Manual  • 2570-981 Rev. B  •  5/20

3.6  Battery Pack Location / Control Cavity

NOTICE:  

Some functionality will be lost when using battery 

backup including any other auxiliary functions that require 

household 220/240 VAC power.

J.  Operation During A Power Outage 

The  IntelliFire™  Plus  intermittent  pilot  ignition  system 

comes  with  a  battery  backup  system  that  enables  the 

system to operate in a power outage.  The system offers 

seamless transition from household AC power to battery 

backup. A factory-installed battery pack is located in the 

control  cavity  of  the  appliance.  See  Figure  3.6.  Battery 

longevity and performance will be affected by long term 

exposure to the service temperatures of this appliance.

NOTICE: 

Batteries should only be used as a power source 

in the event of an emergency power outage. Batteries 

should not be used as a primary long-term power source. 

To Operate Fireplace Using Battery Power (DC):

1.  Access the control cavity of the appliance.  See Figure 

3.6 for location.  Lift the decorative barrier front off of the 

appliance and lift the vanity panel out of the bottom of the 

glass frame.

2.  Locate the battery tray and insert four AA cell batteries. 

See  Figure  3.6.    Battery  polarity  must  be  correct  or 

module damage will occur.  A complete wiring diagram 

is  included  in  the  Electrical  section  of  the  appliance 

Installation Manual.

3.  Turn the appliance on according to the instructions below 

for the appropriate type of control:

Standard Wall Switch or Factory-Installed ON/OFF
Switch: 
•    Toggle the switch as you would under normal 

circumstances.

Optional Wireless Remote: 
•    Remote receiver is integrated into the ignition module
•    Use the remote to turn the appliance on.
•    To preserve battery life, do not use the HI/LO flame or 

THERMOSTAT options.  

Ignition Module:
•  Locate the ignition module in the control cavity.
•    Slide the ON/REMOTE/OFF switch to the ON position.

To Return to Operation Using Electrical (AC) Power

Standard  Wall  Switch  or  Factory-Installed  ON/OFF 

Switch: 

• 

Remove screws on left and right sides of component 

heat shield and lift it out of the control cavity. 

•   Toggle the switch to OFF. 

• R

emove the batteries from the battery tray.  

• 

Reinstall component heat shield. 

• 

Replace door or decorative barrier front on appliance.

CAUTION! 

Risk of Overheating! 

Component heat shield 

MUST be installed before operating appliance. Electrical 

components will be damaged.

Optional Wireless Remote:

• 

Remove screws on left and right sides of component 

heat shield and lift it out of the control cavity. 

•    Slide  the  ON/REMOTE/OFF  switch  to  the  REMOTE 

position.  

•  Remove the batteries from the battery tray. 
•  Reinstall component heat shield. 
• .  Replace door or decorative barrier front on appliance.

Ignition Module:

• 

Remove screws on left and right sides of component 

heat shield and lift it out of the control cavity. 

•    Slide  the  ON/REMOTE/OFF  switch  to  the  REMOTE 

position.  

•  Remove the batteries from the battery tray. 
•  Reinstall component heat shield. 
•    Replace door or decorative barrier front on appliance.

CAUTION! 

Risk of Overheating! 

Component heat shield 

MUST be installed before operating appliance. Electrical 

components will be damaged.

Backup Battery

    

  

Note:  

The battery backup system is disabled if  Power 

Vent option has been installed for use with this 

appliance.

Summary of Contents for B41L-AU





























Reviews: