background image

1

07/22

7027-804H 

Installation and service of this appliance should be performed by 

qualified personnel. Hearth & Home Technologies recommends 

HHT Factory Trained or NFI certified professionals.

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation. 

OWNER: Retain this manual for future reference. 

NOTICE: DO NOT DISCARD THIS MANUAL

R

CB1200 PELLET INSERT 

APPLIANCE 

MODEL:

CB1200I-C

NOTE:

 To obtain a French translation of this manual, 

please contact your dealer or visit 

www.quadrafire.com

REMARQUE :

 Pour obtenir une traduction française de 

ce manuel, s’il vous plaît contacter votre revendeur ou 

visitez 

www.quadrafire.com

Check building codes prior to installation.

•  Installation MUST comply with local, regional, state 

and national codes and regulations.

• 

Consult  local  building,  fire  officials  or  authorities 

having jurisdiction about restrictions, installation 

inspection, and permits.

CAUTION

If the information in these instructions is 

not  followed  exactly,  a  fire  could  result 

causing property damage, personal 

injury, or death.

• 

Do not store or use gasoline or other flammable vapors 

and liquids in the vicinity of this or any other appliance.

• 

Do not over fire

 - If appliance or chimney connector 

glows,  you  are  over  firing.  Over  firing  will  void 

your warranty.

•  Comply with all minimum clearances to combustibles 

as specified. Failure to comply may cause house fire.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during 

operation AND cool down.

Hot glass will cause burns.

•  Do not touch glass until it is cooled
•  NEVER allow children to touch glass
•  Keep children away
•  CAREFULLY SUPERVISE children in same room 

as fireplace.

•  Alert children and adults to hazards of 

high temperatures

•  High temperatures may ignite clothing or other 

flammable materials.

•  Keep clothing, furniture, draperies and other 

flammable materials away.

WARNING

Tested and approved for wood pellets only. Burning of 

any other type of fuel voids your warranty.

CAUTION

Summary of Contents for Quadra-Fire CB1200

































Reviews: