background image

20

07/22

7027-804H 

D. Full Reline With Outside Air - Vertical

NOTE: 

Check clearances carefully for this type of 

installation to ensure adequate room for outside air 

venting.

NOTE:

 In Canada only a full reline is allowed per 

ULC 

S628, ORD ULC C1482-M1990

.

Outside Air

 Termination 

at

 Chimney Top

(Vertical)

305mm  min. 

below

305mm min. 

above

NOTE;  Use non-combustible 

materials around exhaust vent pipe 

and seal all edges with 

non-flammable insulation such as 

mineral wool or ceramic.

Do not use high temperature 

caulking materials to seal any edge 

to prevent furture serviceability.

Figure 20.1

NOTE:

 In Canada this fireplace insert must be installed 

with a continuous chimney liner extending from the 

fireplace insert to the top of the chimney. The chimney 

liner must conform to the Class 3 requirements of 

CAN/

ULC-S635, Standard for Lining Systems for Existing 

Masonry or Factory-Built Chimneys and Vents, or 

CAN/ULC-S640, Standard for Lining Systems for New 

Masonry Chimneys

.

Check building codes prior to installation.

•  Installation MUST comply with local, regional, state 

and national codes and regulations.

• 

Consult  local  building,  fire  officials  or  authorities 

having jurisdiction about restrictions, installation 

inspection, and permits.

CAUTION

Summary of Contents for Quadra-Fire CB1200

































Reviews: