background image

Hearthstone  Quality  Home  Heating Products,  Inc                                                                                

               Bristol  Model  8763 

 

 

During  the  first  few  hours  of  operation  the  applianc e 
may produce  smoke and/or  odor.  This is normal  during 
the first several  burns and also after long periods  when 
the  stove  is  not  burned.  During  these  initial  burns,  
open  a  window(s)  to  assist  in  the  removal  of  the 
smoke/odor. 

 

The  appliance  and  its individual  shutoff  valve  must be 
disconnected  from  the  gas  supply  piping  system 
during  any  pressure  testing  of  that  system  at  test 
pressures  in  excess  of  ½  psig.  (3.5k  Pa).  The 
appliance  must be  isolated from  the gas supply piping 
system by  closing  its individual  manual  shutoff  valve 
during  any  pressure  testing  of  the  gas  supply  piping 
system at test pressures  equal  to  or  less than  ½  psig 
(3.5k Pa). 

 

Fire Hazard 

Do  not  store  or  use  gasoline  or  other  flammable 
vapors  or liquids in the vicinity of this appliance.  Locate 
the Bristol out of  traffic  areas  and  away  from  furniture,  
draperies,  clothing, and  flammable  material. 
 

Vent Only to the Outside 

Never  vent  the gas heater  to other  rooms or  buildings.  
 

Service Caution 

If  you  believe  your  Bristol  is  not,  in  any  way, 
performing 

properly, 

immediately 

discontinue 

operation  until  the  unit  is  inspected  and  approved  by 
qualified  service  personnel.   Prior to servicing  the unit, 
turn  the  gas  to  the  valve  off,  and  disconnect  any  
electrical  source.  Ensure  the  unit  is  cool  prior  to 
servicing  and  cleaning.  Replace  any  safety  screen,  
guard,  or component  removed  during  servicing  prior  to 
operation.  Use  of  any  components  not  supplied  by 
Hearthstone  on the  stove  voids  all  warranties. 

Do not 

substitute  components. 
 

Proper Fuel 

This  gas  heater  is designed  to  burn  natural  gas  (NG) 
or  with  conversion,  liquid  propane  (LP).  Never  burn 
any  fuel  gas  not intended  for  use  with this unit. Never 
burn  paper,  wood,  or other  materials  in this appliance.  

This  heater  is  factory  equipped  to  burn  natural  gas  
(NG).  To  burn  propane  (LP),  you  must  install  the 
included  LP conversion  kit #97-56631. 

This  appliance  is only  for  use  with  the  type(s)  of  gas  
indicated  on  the  rating  plate.  This  appliance  is  not  
convertible  for  use  with other  gases, unless a certified 
kit  is  used.

  Cet  appareil  doit  être  atilisé  uniquement  

avec  les  types  de  gas  indiqués  sur  la  plaque 
signalétique. Ne pas l’utiliser avec d’autres  gas sauf si 
un  k ited conversion  certifié est installé. ) 

 

WARNING:  THIS  GAS  APPLIANCE  MUST  NOT  BE 
CONNECTED  TO  A  CHIMNEY  FLUE  SERVING  A 
SEPARATE 

GAS 

OR 

SOLID-FUEL 

BURNING 

APPLIANCE 

 

WARNING:    DO  NOT  OPERATE  THE  APPLIANCE 
WITH  THE  FRONT  GLASS  REMOVED,  CRACKED, 
OR BROKEN.   REPLACEMENT  OF  GLASS  SHOULD 
BE  DONE  BY  A LICENSED  OR QUALIFIED  SERVICE 
PERSON.    ONLY  OPEN  FRONT  FOR  ROUTINE 
SERVICE.    DO  NOT  SLAM    FRONT  OR  STRIKE 
GLASS.  USE MANUFACTURER-APPROVED  FRONT 
GLASS  ONLY.

 

 

WARNING:  HEARTHSTONE  RECOMMENDS  THAT 
ONLY  AN  NFI  CERTIFIED  SERVICE  TECHNICIA N 
INSTALLS,  AND  REPAIRS  THIS  APPLIANCE.  A 
QUALIFIED  SERVICE  TECHNICIAN  MUST  INSPECT 
THE  APPLIANCE  BEFORE  USE,  AND  AT  LEAST 
ANNUALLY.  MORE  FREQUENT  CLEANING  MAY  BE 
REQUIRED 

DUE  TO  EXCESSIVE 

LINT  FROM 

CARPETING,  BEDDING  MATERIAL,  PETS,  ETC.  IT 
IS 

IMPERATIVE 

THAT 

THE 

CONTROL 

COMPARTMENTS,  BURNERS,  AND  CIRCULATI N G 
AIR  PASSAGES  OF  THE  APPLIANCE  ARE  KEPT 
CLEAN 

AND 

FREE 

OF 

OBSTRUCTIONS. 

(S’ASSURER 

QUE 

LE 

BRÛLEUR 

ET 

LE 

COMPARTIMENT 

DES 

COMMANDES 

SONT 

PROPRES. 

 

VOIR 

LES 

INSTRUCTIONS 

D’INSTALLATION 

ET 

D’UTILISATION 

QUI 

ACCOMPAGNENT L’APPAREIL.) 
 

Hot Surfaces 

Certain  exposed  surfaces  of  the Bristol will reach  high 
temperatures  during  normal  operation.   Clearances  to 
combustibles  must  be  maintained,  as  specified  in the 
“Clearances  To Combustibles”  section of this manual.   
 

 

DUE  TO  HIGH  TEMPERATURES  THE  APPLIANCE 
SHOULD  BE  LOCATED  OUT  OF  TRAFFIC  AND 
AWAY  FROM  FURNITURE,  DRAPERIES,  CLOTHING 
AND  FLAMMABLE  MATERIALS.    EN  RAISON DES 
TEMPÉRATURES ÉLEVÉES, L’APPAREIL DEVRAIT 
ÊTRE INSTALLÉ DANS UN ENDROIT OÙ IL Y A PEU 
DE CIRCULATION  ET  LOIN  DU MOBILIER  ET  DES 
TENTURES 

 

CHILDREN  AND ADULTS  SHOULD  BE ALERTED  TO 
THE 

HAZARDS 

OF 

HIGH 

SURFACE 

TEMPERATURES  AND  SHOULD  STAY  AWAY  TO 
AVOID  BURNS  TO  SKIN  OR  CLOTHING  IGNITION. 
LES ENFANTS ET LES ADULTES DEVRAIENT ÊTRE 
INFORMÉS  DES  DANGERS  QUE  POSENT  LES 
TEMPÉRATURES  DE  SURFACE  ÉLEVÉES  ET  SE 
TENIR 

À 

DISTANCE 

AFIN 

D’ÉVITER  DES 

BRÛLURES  OU  QUE  LEURS  VÊTEMENTS  NE 
S’ENFLAMMENT.
 

 

CAREFULLY 

SUPERVISE 

YOUNG 

CHILDREN 

WHEN  THEY  ARE  IN  THE  SAME  ROOM  AS  THE 
APPLIANCE.  TODDLERS,  YOUNG  CHILDREN,  AND 
OTHERS  MAY  BE  SUSCEPTIBLE  TO  ACCIDENT AL 
CONTACT 

BURNS.

 

BARRIERS 

DESIGNED 

TO 

Summary of Contents for 8763)


















































Reviews: